Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2020.08
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Blind Spot Monitor Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Blind Spot Monitor Sensor Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Blind Spot Monitor Master" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Blind Spot Monitor Master" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Blind Spot Monitor Master" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Blind Spot Monitor Sensor Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Blind spot monitor sensor LH branch line or connector

·

Power source circuit of blind spot monitor sensor LH

·

Blind spot monitor sensor LH ground circuit

·

Blind spot monitor sensor LH



WIRING DIAGRAM

C369914E07
1.635,0.542 1.792,0.74 0.156,0.198 10 false 9 1.625,1.073 1.896,1.271 0.271,0.198 10 false 20 0.25,1.573 0.677,1.771 0.427,0.198 10 false M104 0.25,1.74 2.177,1.948 1.927,0.208 10 false No. 6 CAN Junction Connector 5.583,0.542 5.74,0.74 0.156,0.198 10 false 2 5.594,1.083 5.75,1.281 0.156,0.198 10 false 7 5.813,0.646 6.396,0.833 0.583,0.188 10 false CA1P 5.813,1.156 6.396,1.344 0.583,0.188 10 false CA1N 5.813,2.24 6.396,2.427 0.583,0.188 10 false BLB 5.813,3.115 6.396,3.302 0.583,0.188 10 false BLGD 4.167,2.385 5.448,2.604 1.281,0.219 10 false ECU-IG1 NO. 4 5.271,3.438 5.698,3.646 0.427,0.208 10 false M62 5.271,3.604 7.135,3.865 1.865,0.26 10 false Blind Spot Monitor Sensor LH 2.115,2.198 3.531,2.458 1.417,0.26 10 false from IG1-NO. 1 Relay 5.594,2.146 5.75,2.344 0.156,0.198 10 false 5 5.531,3.01 5.771,3.208 0.24,0.198 10 false 10

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (BLIND SPOT MONITOR SENSOR LH BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the blind spot monitor sensor LH connector.


c.
C422773C01
1.469,0.719 1.938,0.938 0.469,0.219 1.49,1.906 1.125,1.156 true 1.5,2.177 1.167,2.865 true 0.146,0.135 0.458,0.292 0.313,0.156 10 false *a 1.573,0.74 1.885,0.896 0.313,0.156 10 false M62 0.708,1.052 1.323,1.25 0.615,0.198 10 false CA1P 0.719,2.813 1.333,3.01 0.615,0.198 10 false CA1N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M62-2 (CA1P) - M62-7 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C422773C02
1.469,0.719 1.844,0.938 0.375,0.219 2.094,1.917 2.427,1.167 true 2.073,2.188 2.458,2.885 true 0.146,0.135 0.458,0.292 0.313,0.156 10 false *a 1.531,0.74 1.844,0.896 0.313,0.156 10 false M62 2.542,1.063 3.156,1.26 0.615,0.198 10 false BLB 2.552,2.813 3.167,3.01 0.615,0.198 10 false BLGD
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M62-10 (BLGD) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M62-5 (BLB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)