Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2020.08
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Parking Assist ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Parking Assist ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Panoramic View Monitor / Circumference Monitoring Camera Control Module" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Panoramic View Monitor / Circumference Monitoring Camera Control Module" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Panoramic View Monitor / Circumference Monitoring Camera Control Module" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Parking Assist ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Parking assist ECU branch line or connector

·

Power source circuit of parking assist ECU

·

Parking assist ECU ground circuit

·

Parking assist ECU



WIRING DIAGRAM

C404394E02
5.448,0.906 5.865,1.104 0.417,0.198 10 false CANH 5.438,1.344 5.854,1.542 0.417,0.198 10 false CANL 5.448,2.417 5.865,2.615 0.417,0.198 10 false +B 5.438,2.958 5.854,3.156 0.417,0.198 10 false +B2 5.448,3.479 5.865,3.677 0.417,0.198 10 false IG 5.448,4.021 5.865,4.219 0.417,0.198 10 false ACC 5.458,4.531 5.875,4.729 0.417,0.198 10 false GND1 5.448,5.063 5.865,5.26 0.417,0.198 10 false GND2 5.177,1.26 5.417,1.438 0.24,0.177 10 false 18 5.24,2.333 5.427,2.521 0.188,0.188 10 false 1 5.198,2.844 5.385,3.031 0.188,0.188 10 false 19 5.208,3.365 5.406,3.552 0.198,0.188 10 false 21 5.24,3.906 5.406,4.094 0.167,0.188 10 false 3 5.229,4.438 5.396,4.625 0.167,0.188 10 false 2 5.208,4.958 5.406,5.146 0.198,0.188 10 false 20 5.188,0.844 5.385,1.021 0.198,0.177 10 false 40 1.573,0.813 1.771,0.99 0.198,0.177 10 false 4 1.552,1.24 1.76,1.427 0.208,0.188 10 false 10 0.208,1.646 0.625,1.844 0.417,0.198 10 false F164 0.198,1.813 2.625,2.063 2.427,0.25 10 false No. 1 CAN Junction Connector 2.094,2.396 3.177,2.583 1.083,0.188 10 false from Battery 1.531,3.469 3.188,3.708 1.656,0.24 10 false from IG1 NO. 1 Relay 1.792,3.99 2.781,4.198 0.99,0.208 10 false from ACC Relay 3.646,2.583 4.51,2.781 0.865,0.198 10 false ECU-B NO. 2 3.542,3.635 4.823,3.896 1.281,0.26 10 false ECU-IG 1 NO. 4 3.688,4.156 4.708,4.427 1.021,0.271 10 false ECU-ACC 5.344,5.708 5.75,5.896 0.406,0.188 10 false M116 5.344,5.885 6.76,6.198 1.417,0.313 10 false Parking Assist ECU

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (PARKING ASSIST ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the parking assist ECU connector.


c.
C403821C06
1.458,0.844 1.958,1.094 0.5,0.25 3.042,1.74 1.802,2.688 true 3.01,1.917 2.708,2.677 true 1.542,0.885 2.156,1.083 0.615,0.198 10 false M116 1.635,2.708 2.25,2.906 0.615,0.198 10 false CANL 2.542,2.708 3.156,2.906 0.615,0.198 10 false CANH 0.094,0.094 0.708,0.292 0.615,0.198 10 false *a
*a Front view of wire harness connector
(to Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M116-40 (CANH) - M116-18 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (PARKING ASSIST ECU)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C403821C07
1.458,0.844 1.958,1.094 0.5,0.25 0.417,1.927 0.177,2.833 true 0.573,1.938 0.885,2.875 true 0.677,1.917 1.406,2.854 true 0.375,1.656 0.604,0.49 true 0.531,1.677 0.813,0.771 true 0.646,1.667 0.896,1.073 true 1.563,0.906 2.177,1.104 0.615,0.198 10 false M116 0.063,2.917 0.427,3.115 0.365,0.198 10 false +B2 0.688,0.417 1.021,0.583 0.333,0.167 10 false +B 0.094,0.094 0.708,0.292 0.615,0.198 10 false *a 0.75,2.906 1.208,3.146 0.458,0.24 10 false GND2 1.375,2.906 1.74,3.104 0.365,0.198 10 false IG 0.865,0.708 1.479,0.906 0.615,0.198 10 false GND1 0.958,0.99 1.573,1.188 0.615,0.198 10 false ACC
*a Front view of wire harness connector
(to Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M116-2 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
M116-20 (GND2) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M116-1 (+B) - Body ground Always 11 to 14 V
M116-19 (+B2) - Body ground Always 11 to 14 V
M116-3 (ACC) - Body ground Ignition switch ACC 11 to 14 V
M116-21 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)