Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2020.08
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 3 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
·

Short in CAN main bus lines

·

Short in CAN branch lines

·

Radio and display receiver assembly

(for Radio and Display Type)

·

Telematics transceiver

(w/ Manual (SOS) Switch)

·

Central gateway ECU (network gateway ECU)

·

No. 3 CAN junction connector



WIRING DIAGRAM

C360943E06
0.677,0.969 1.448,1.167 0.771,0.198 10 false 120 Ω 0.677,3.156 1.448,3.354 0.771,0.198 10 false 120 Ω 1.375,0.625 2.146,0.823 0.771,0.198 10 false CA3H 1.875,0.625 2.646,0.823 0.771,0.198 10 false 6 2.823,0.625 3.594,0.823 0.771,0.198 10 false 10 1.844,1.146 2.615,1.344 0.771,0.198 10 false 21 1.396,1.146 2.167,1.344 0.771,0.198 10 false CA3L 2.823,1.146 3.594,1.344 0.771,0.198 10 false 21 4.198,0.615 4.969,0.813 0.771,0.198 10 false 8 4.156,1.135 4.927,1.333 0.771,0.198 10 false 19 5.167,0.625 5.938,0.823 0.771,0.198 10 false 15 5.156,1.146 5.927,1.344 0.771,0.198 10 false 16 5.427,0.698 6.198,0.896 0.771,0.198 10 false CANP 5.427,1.24 6.198,1.438 0.771,0.198 10 false CANN 5.448,2.833 6.219,3.031 0.771,0.198 10 false CANH 5.146,3.281 5.917,3.479 0.771,0.198 10 false 14 5.146,2.76 5.917,2.958 0.771,0.198 10 false 13 5.458,3.354 6.229,3.552 0.771,0.198 10 false CANL 5.208,3.771 5.979,3.969 0.771,0.198 10 false F131 5.208,3.958 6.948,4.354 1.74,0.396 10 false Radio and Display Receiver Assembly*2 2.813,3.979 4.823,4.323 2.01,0.344 10 false No. 4 CAN Junction Connector 2.823,3.813 3.594,4.01 0.771,0.198 10 false F114 2.833,3.292 3.604,3.49 0.771,0.198 10 false 22 2.833,2.76 3.604,2.958 0.771,0.198 10 false 11 4.177,2.75 4.948,2.948 0.771,0.198 10 false 9 4.167,3.281 4.938,3.479 0.771,0.198 10 false 20 1.823,3.292 2.594,3.49 0.771,0.198 10 false 20 1.833,2.75 2.604,2.948 0.771,0.198 10 false 19 1.333,2.75 2.104,2.948 0.771,0.198 10 false CAYH 1.354,3.292 2.125,3.49 0.771,0.198 10 false CAYL 0.229,3.781 1,3.979 0.771,0.198 10 false F74 0.229,3.958 2.208,4.396 1.979,0.438 10 false Central Gateway ECU (Network Gateway ECU) 0.24,5 3.302,5.333 3.063,0.333 10 false *1: w/ Manual (SOS) Switch 0.229,5.333 3.021,5.708 2.792,0.375 10 false *2: for Radio and Display Type 5.229,1.625 6,1.823 0.771,0.198 10 false F51 5.198,1.802 6.938,2.229 1.74,0.427 10 false Telematics Transceiver*1

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS LINES (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 3 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C366168C82
3.333,1.083 3.833,1.333 0.5,0.25 4.75,1.333 4.083,1.844 true 4.198,1.854 4.75,1.667 true 4.073,2.063 4.75,2.667 true 4.188,2.052 4.75,2.333 true 4.75,1 3.958,1.844 true 3.938,2.063 4.75,3 true 4.76,0.615 3.823,1.833 true 3.813,2.052 4.771,3.281 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 3.427,1.125 4.042,1.323 0.615,0.198 10 false F114 4.823,0.896 5.406,1.083 0.583,0.188 10 false CANH*c 4.823,1.229 5.406,1.417 0.583,0.188 10 false CANH*d 4.823,2.563 5.375,2.76 0.552,0.198 10 false CANL*d 4.823,2.896 5.375,3.094 0.552,0.198 10 false CANL*c 4.823,2.229 5.375,2.427 0.552,0.198 10 false CANL*d 4.823,1.563 5.406,1.75 0.583,0.188 10 false CANH*d 4.823,0.51 5.406,0.698 0.583,0.188 10 false CANH*b 4.823,3.208 5.375,3.406 0.552,0.198 10 false CANL*b
*a Front view of wire harness connector
(to No. 3 CAN junction connector)
*b to Telematics Transceiver
(w/ Manual (SOS) Switch)
*c to Radio and Display Receiver Assembly
(for Radio and Display Type)
*d to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F114-8 (CANH) - F114-19 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Telematics transceiver*1
F114-9 (CANH) - F114-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Radio and display receiver assembly*2
F114-10 (CANH) - F114-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
F114-11 (CANH) - F114-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)


*1: w/ Manual (SOS) Switch

*2: for Radio and Display Type



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to ECU or sensor) C



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT IN CAN BUS LINES (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

3.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
2.CHECK FOR SHORT IN CAN BUS LINES (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.
C422786C01
1.417,0.75 1.917,1 0.5,0.25 2.292,1.74 2.135,1.25 true 2.521,1.75 2.75,1.167 true 2.125,2.49 2.292,2.021 true 2.75,2.5 2.521,2.021 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.51,0.792 1.906,0.958 0.396,0.167 10 false E66 2.813,1.083 3.365,1.333 0.552,0.25 10 false CANH*b 1.552,1.125 2.198,1.292 0.646,0.167 10 false CANH*b 1.917,2.531 2.563,2.698 0.646,0.167 10 false CANL*b 2.74,2.542 3.292,2.708 0.552,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F114-10 (CANH) - F114-21 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher
F114-11 (CANH) - F114-22 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

B

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

3.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C367308C14
1.458,0.167 1.958,0.417 0.5,0.25 1.01,1.75 1.427,1.104 true 1.406,1 1.094,0.5 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.594,0.198 2.052,0.396 0.458,0.198 10 false F74 0.667,0.396 1.281,0.594 0.615,0.198 10 false CA3H 0.594,1.646 1.208,1.844 0.615,0.198 10 false CA3L
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-6 (CA3H) - F74-21 (CA3L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR