Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2020.08
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 4 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 22 (CA2H) and 7 (CA2L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 22 (CA2H) and 7 (CA2L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
·

Short in CAN main bus lines

·

Short in CAN branch lines

·

Central gateway ECU (network gateway ECU)

·

Airbag sensor assembly

·

Steering sensor

·

Power steering ECU assembly

·

Brake actuator assembly

·

4WD ECU assembly

(for AWD)

·

No. 5 CAN junction connector

(for LHD)

·

No. 4 CAN junction connector

(for LHD)

·

No. 4 CAN junction connector

(for RHD)

·

No. 5 CAN junction connector

(for RHD)



WIRING DIAGRAM

for LHD


C360945E02
1.354,0.719 1.917,0.917 0.563,0.198 10 false CANH 1.354,1.26 1.917,1.458 0.563,0.198 10 false CANL 1.854,0.615 2.083,0.813 0.229,0.198 10 false 5 1.854,1.156 2.083,1.354 0.229,0.198 10 false 19 2.885,0.604 3.115,0.802 0.229,0.198 10 false 5 2.823,1.167 3.052,1.365 0.229,0.198 10 false 16 4.188,0.604 4.417,0.802 0.229,0.198 10 false 2 4.188,1.167 4.417,1.365 0.229,0.198 10 false 13 5.167,0.625 5.396,0.823 0.229,0.198 10 false 22 5.219,1.146 5.448,1.344 0.229,0.198 10 false 7 5.427,0.615 5.99,0.813 0.563,0.198 10 false CA2H 5.438,1.167 6,1.365 0.563,0.198 10 false CA2L 6.083,1.01 6.646,1.208 0.563,0.198 10 false 120 Ω 5.115,1.594 5.677,1.792 0.563,0.198 10 false F74 5.104,1.76 7.104,2.208 2,0.448 10 false Central Gateway ECU (Network Gateway ECU) 4.167,2.75 4.396,2.948 0.229,0.198 10 false 1 4.177,3.323 4.406,3.521 0.229,0.198 10 false 12 2.875,2.75 3.104,2.948 0.229,0.198 10 false 6 2.833,3.302 3.063,3.5 0.229,0.198 10 false 17 1.854,2.76 2.083,2.958 0.229,0.198 10 false 6 1.865,3.313 2.094,3.51 0.229,0.198 10 false 5 1.344,2.854 1.906,3.052 0.563,0.198 10 false CANH 1.354,3.396 1.917,3.594 0.563,0.198 10 false CANL 0.5,1.635 1.063,1.833 0.563,0.198 10 false A42 0.5,1.833 2.167,2.083 1.667,0.25 10 false Brake Actuator Assembly 0.479,3.75 1.042,3.948 0.563,0.198 10 false M77 0.49,3.938 2.052,4.135 1.563,0.198 10 false 4WD ECU Assembly*1 2.927,3.771 3.49,3.969 0.563,0.198 10 false F124 2.927,3.938 4.24,4.385 1.313,0.448 10 false No. 5 CAN Junction Connector 0.438,5 2,5.198 1.563,0.198 10 false *1: for AWD

C360946E03
1.344,1.281 1.958,1.479 0.615,0.198 10 false CANH 1.354,1.802 1.969,2 0.615,0.198 10 false CANL 1.865,1.167 2.115,1.333 0.25,0.167 10 false 7 1.854,1.698 2.104,1.865 0.25,0.167 10 false 8 2.875,1.156 3.125,1.323 0.25,0.167 10 false 6 2.813,1.698 3.063,1.865 0.25,0.167 10 false 17 4.177,1.146 4.427,1.313 0.25,0.167 10 false 7 4.167,1.708 4.417,1.875 0.25,0.167 10 false 18 0.417,2.135 1.031,2.333 0.615,0.198 10 false F23 0.417,2.292 2.448,2.542 2.031,0.25 10 false Power Steering ECU Assembly 1.354,3.323 1.969,3.521 0.615,0.198 10 false CANH 1.385,3.854 2,4.052 0.615,0.198 10 false CANL 0.708,3.667 1.323,3.865 0.615,0.198 10 false 120 Ω 0.344,4.323 0.958,4.521 0.615,0.198 10 false F150 0.323,4.479 1.906,4.677 1.583,0.198 10 false Airbag Sensor Assembly 1.833,3.323 2.083,3.49 0.25,0.167 10 false 26 1.854,3.844 2.104,4.01 0.25,0.167 10 false 27 2.896,3.323 3.146,3.49 0.25,0.167 10 false 1 2.833,3.854 3.083,4.021 0.25,0.167 10 false 12 4.188,3.302 4.438,3.469 0.25,0.167 10 false 5 4.167,3.854 4.417,4.021 0.25,0.167 10 false 16 5.229,3.323 5.479,3.49 0.25,0.167 10 false 3 5.24,3.865 5.49,4.031 0.25,0.167 10 false 2 5.458,3.406 6.073,3.604 0.615,0.198 10 false CANH 5.458,3.948 6.073,4.146 0.615,0.198 10 false CANL 5.438,4.333 6.052,4.531 0.615,0.198 10 false F69 5.438,4.5 6.604,4.75 1.167,0.25 10 false Steering Sensor 2.75,4.313 3.365,4.51 0.615,0.198 10 false F123 2.75,4.5 4.865,4.698 2.115,0.198 10 false No. 4 CAN Junction Connector


for RHD


C360948E02
1.333,0.719 1.896,0.917 0.563,0.198 10 false CANH 1.365,1.25 1.927,1.448 0.563,0.198 10 false CANL 1.875,0.604 2.208,0.771 0.333,0.167 10 false 5 1.854,1.156 2.188,1.323 0.333,0.167 10 false 19 2.875,0.594 3.208,0.76 0.333,0.167 10 false 7 2.802,1.177 3.135,1.344 0.333,0.167 10 false 18 4.198,0.615 4.531,0.781 0.333,0.167 10 false 2 4.188,1.156 4.521,1.323 0.333,0.167 10 false 13 4.177,1.469 4.51,1.635 0.333,0.167 10 false 12 4.188,1.729 4.521,1.896 0.333,0.167 10 false 1 5.167,0.625 5.5,0.792 0.333,0.167 10 false 22 5.24,1.167 5.573,1.333 0.333,0.167 10 false 7 5.438,0.615 6,0.813 0.563,0.198 10 false CA2H 5.427,1.167 5.99,1.365 0.563,0.198 10 false CA2L 6.104,0.99 6.667,1.188 0.563,0.198 10 false 120 Ω 5.177,1.625 5.74,1.823 0.563,0.198 10 false F74 5.167,1.781 7.156,2.229 1.99,0.448 10 false Central Gateway ECU (Network Gateway ECU) 2.594,2.167 3.156,2.365 0.563,0.198 10 false F117 2.594,2.323 4.594,2.521 2,0.198 10 false No. 5 CAN Junction Connector 0.438,1.583 1,1.781 0.563,0.198 10 false A42 0.438,1.76 2.167,2.01 1.729,0.25 10 false Brake Actuator Assembly 1.344,3.469 1.906,3.667 0.563,0.198 10 false CANH 1.375,3.99 1.938,4.188 0.563,0.198 10 false CANL 1.865,3.354 2.198,3.521 0.333,0.167 10 false 6 1.865,3.906 2.198,4.073 0.333,0.167 10 false 5 2.885,3.354 3.219,3.521 0.333,0.167 10 false 4 2.833,3.896 3.167,4.063 0.333,0.167 10 false 15 4.188,3.354 4.521,3.521 0.333,0.167 10 false 6 4.198,3.896 4.531,4.063 0.333,0.167 10 false 17 0.594,4.354 0.927,4.521 0.333,0.167 10 false M77 0.594,4.531 2.094,4.781 1.5,0.25 10 false 4WD ECU Assembly*1 4.188,4.333 4.802,4.531 0.615,0.198 10 false F115 4.188,4.5 6.313,4.792 2.125,0.292 10 false No. 4 CAN Junction Connector 0.344,5.219 1.844,5.469 1.5,0.25 10 false *1: for AWD

C360949E03
1.344,1.688 1.958,1.885 0.615,0.198 10 false CANH 1.375,2.208 1.99,2.406 0.615,0.198 10 false CANL 1.865,1.594 2.063,1.76 0.198,0.167 10 false 7 1.865,2.125 2.063,2.292 0.198,0.167 10 false 8 2.896,1.583 3.094,1.75 0.198,0.167 10 false 3 2.833,2.115 3.083,2.281 0.25,0.167 10 false 14 4.219,1.583 4.469,1.75 0.25,0.167 10 false 5 4.167,2.125 4.417,2.292 0.25,0.167 10 false 16 5.198,2.115 5.448,2.281 0.25,0.167 10 false 2 5.208,1.583 5.406,1.75 0.198,0.167 10 false 3 5.438,1.698 6.052,1.896 0.615,0.198 10 false CANH 5.448,2.198 6.063,2.396 0.615,0.198 10 false CANL 0.49,2.573 1.104,2.771 0.615,0.198 10 false F23 0.5,2.75 2.667,2.948 2.167,0.198 10 false Power Steering ECU Assembly 5.406,2.583 6.021,2.781 0.615,0.198 10 false F69 5.396,2.74 6.563,2.99 1.167,0.25 10 false Steering Sensor 2.875,3.667 3.125,3.833 0.25,0.167 10 false 1 2.833,4.198 3.083,4.365 0.25,0.167 10 false 12 1.833,3.656 2.083,3.823 0.25,0.167 10 false 26 1.854,4.188 2.104,4.354 0.25,0.167 10 false 27 1.344,3.667 1.958,3.865 0.615,0.198 10 false CANH 1.365,4.198 1.979,4.396 0.615,0.198 10 false CANL 0.698,4 1.313,4.198 0.615,0.198 10 false 120 Ω 0.5,4.677 1.115,4.875 0.615,0.198 10 false F150 0.49,4.823 2.24,5.021 1.75,0.198 10 false Airbag Sensor Assembly 2.76,4.646 3.375,4.844 0.615,0.198 10 false F115 2.75,4.833 4.75,5 2,0.167 10 false No. 4 CAN Junction Connector


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR)

B

6.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 5 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C366168C15
3.333,1.083 3.833,1.333 0.5,0.25 2.417,2.333 2.927,2.063 true 3.417,2.063 2.542,3.167 true 2.417,1.667 2.917,1.844 true 2.333,1.25 3.083,1.844 true 2.333,2.75 3.083,2.063 true 2.333,0.833 3.417,1.854 true 4.583,0.75 3.615,1.844 true 4.25,3.083 3.604,2.063 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.833,1.531 2.427,1.729 0.594,0.198 10 false CANH*b 1.771,1.073 2.365,1.26 0.594,0.188 10 false CANH*c 1.76,0.698 2.344,0.885 0.583,0.188 10 false CANH*d 3.427,1.125 4.042,1.323 0.615,0.198 10 false F124 1.854,2.281 2.417,2.469 0.563,0.188 10 false CANL*b 1.792,2.698 2.354,2.896 0.563,0.198 10 false CANL*c 1.979,3.135 2.542,3.323 0.563,0.188 10 false CANL*d 4.656,0.656 5.24,0.844 0.583,0.188 10 false CANH*e 4.26,3.115 4.823,3.302 0.563,0.188 10 false CANL*e
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) *d to Brake Actuator Assembly
*e to 4WD ECU Assembly
(for AWD)
- -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F124-1 (CANH) - F124-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 4 CAN junction connector
F124-2 (CANH) - F124-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
F124-5 (CANH) - F124-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Brake actuator assembly
F124-6 (CANH) - F124-17 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher 4WD ECU Assembly*1


*1: for AWD



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 4 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

3.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

4.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)

D

10.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
3.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.
C366166C13
1.417,0.75 1.917,1 0.5,0.25 1.417,2.583 1.115,2.01 true 1.083,1.75 0.781,1.177 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.521,0.792 1.917,0.958 0.396,0.167 10 false F124 0.198,1.094 0.844,1.26 0.646,0.167 10 false CANH*b 1.479,2.49 2.125,2.656 0.646,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F124-2 (CANH) - F124-13 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

4.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
a.

Reconnect the F124 No. 5 CAN junction connector.


b.

Disconnect the No. 4 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C366168C16
3.333,1.083 3.833,1.333 0.5,0.25 2.417,2.333 2.927,2.063 true 3.458,2.063 2.583,3.167 true 2.417,1.667 2.917,1.844 true 4.333,2.833 3.604,2.063 true 2.542,0.833 3.417,1.833 true 4.333,1.083 3.604,1.833 true 4.333,1.417 3.729,1.844 true 4.333,2.5 3.729,2.063 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.833,1.531 2.427,1.729 0.594,0.198 10 false CANH*b 1.938,0.688 2.531,0.875 0.594,0.188 10 false CANH*c 4.427,0.979 5.01,1.167 0.583,0.188 10 false CANH*d 3.427,1.125 4.042,1.323 0.615,0.198 10 false F123 1.854,2.281 2.417,2.469 0.563,0.188 10 false CANL*b 2.042,3.146 2.604,3.344 0.563,0.198 10 false CANL*c 4.396,2.854 4.958,3.042 0.563,0.188 10 false CANL*d 4.417,1.333 5,1.521 0.583,0.188 10 false CANH*e 4.417,2.479 4.979,2.667 0.563,0.188 10 false CANL*e
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Airbag Sensor Assembly
*c to Steering Sensor *d to Power Steering ECU Assembly
*e to No. 5 CAN Junction Connector - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F123-1 (CANH) - F123-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Airbag sensor assembly
F123-5 (CANH) - F123-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Steering sensor
F123-6 (CANH) - F123-17 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Power steering ECU assembly
F123-7 (CANH) - F123-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 5 CAN junction connector



Result:
Result Proceed to
OK A
NG (Line to No. 5 CAN junction connector) B
NG (Line to Airbag sensor assembly) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 5 CAN JUNCTION CONNECTOR)

C

5.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

D

10.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
5.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the F150 airbag sensor assembly connector.


b.
C366166C24
1.417,0.75 1.917,1 0.5,0.25 1.302,2.594 1,2.021 true 0.927,1.75 0.625,1.177 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.521,0.792 1.917,0.958 0.396,0.167 10 false F123 0.063,1.052 0.708,1.219 0.646,0.167 10 false CANH*b 1.313,2.635 1.958,2.802 0.646,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Airbag Sensor Assembly


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F123-1 (CANH) - F123-12 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

6.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 5 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C366168C17
3.333,1.083 3.833,1.333 0.5,0.25 2.417,2.333 2.927,2.063 true 3.719,2.073 4.375,2.521 true 2.417,1.667 2.917,1.844 true 2.333,1.25 3.083,1.844 true 2.333,2.75 3.083,2.063 true 4.396,1.344 3.729,1.833 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.833,1.531 2.427,1.729 0.594,0.198 10 false CANH*b 1.771,1.073 2.365,1.26 0.594,0.188 10 false CANH*c 4.469,1.26 5.052,1.448 0.583,0.188 10 false CANH*d 3.427,1.125 4.042,1.323 0.615,0.198 10 false F117 1.854,2.281 2.417,2.469 0.563,0.188 10 false CANL*b 1.792,2.698 2.354,2.896 0.563,0.198 10 false CANL*c 4.417,2.51 4.979,2.698 0.563,0.188 10 false CANL*d
*a Front view of wire harness connector
(to No. 8 CAN Junction Connector)
*b to No. 6 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) *d to Brake Actuator Assembly


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F117-1 (CANH) - F117-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 6 CAN junction connector
F117-2 (CANH) - F117-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
F117-7 (CANH) - F117-18 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Brake actuator assembly



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 4 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

7.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

8.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)

D

10.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
7.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.
C366166C25
1.417,0.75 1.917,1 0.5,0.25 1.063,1.76 0.75,1.25 true 0.75,2.5 1.073,2.01 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.5,0.792 1.896,0.958 0.396,0.167 10 false F117 0.167,1.125 0.813,1.292 0.646,0.167 10 false CANH*b 0.26,2.51 0.906,2.677 0.646,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F117-2 (CANH) - F117-13 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

8.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
a.

Reconnect the F117 No. 5 CAN junction connector.


b.

Disconnect the No. 4 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C366168C18
3.333,1.083 3.833,1.333 0.5,0.25 2.417,2.333 2.927,2.063 true 4.333,1 3.49,1.844 true 3.604,1.844 4.5,1.417 true 3.208,2.063 2.313,2.802 true 3.49,2.063 4.333,2.917 true 2.417,1.667 2.917,1.844 true 2.479,0.875 3.302,1.844 true 2.417,1.292 3.208,1.833 true 3.615,2.052 4.5,2.5 true 3.313,2.063 2.417,3.146 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.833,1.531 2.427,1.729 0.594,0.198 10 false CANH*b 1.844,1.167 2.438,1.354 0.594,0.188 10 false CANH*c 1.885,0.802 2.469,0.99 0.583,0.188 10 false CANH*d 3.427,1.125 4.042,1.323 0.615,0.198 10 false F115 1.854,2.281 2.417,2.469 0.563,0.188 10 false CANL*b 1.813,2.771 2.375,2.969 0.563,0.198 10 false CANL*c 1.917,3.156 2.479,3.344 0.563,0.188 10 false CANL*d 4.385,0.833 4.969,1.021 0.583,0.188 10 false CANH*e 4.552,1.292 5.135,1.479 0.583,0.188 10 false CANH*f 4.583,2.417 5.135,2.615 0.552,0.198 10 false CANL*f 4.396,2.885 4.948,3.083 0.552,0.198 10 false CANL*e
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Airbag Sensor Assembly
*c to Power Steering ECU Assembly *d to 4WD ECU Assembly
(for AWD)
*e to Steering Sensor *f to No. 5 CAN Junction Connector


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F115-1 (CANH) - F115-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Airbag sensor assembly
F115-3 (CANH) - F115-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Power steering ECU assembly
F115-4 (CANH) - F115-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher 4WD ECU assembly*1
F115-5 (CANH) - F115-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Steering sensor
F115-6 (CANH) - F115-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 5 CAN junction connector


*1: for AWD



Result:
Result Proceed to
OK A
NG (Line to No. 5 CAN junction connector) B
NG (Line to Airbag sensor assembly) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - NO. 4 CAN JUNCTION CONNECTOR)

C

9.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

D

10.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
9.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the F150 airbag sensor assembly connector.


b.
C366166C14
1.417,0.75 1.917,1 0.5,0.25 0.906,1.74 0.75,1.25 true 0.75,2.5 0.917,2.031 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.521,0.792 1.917,0.958 0.396,0.167 10 false F115 0.167,1.125 0.813,1.292 0.646,0.167 10 false CANH*b 0.313,2.531 0.958,2.698 0.646,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Airbag Sensor Assembly


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F115-1 (CANH) - F115-12 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

10.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C367308C01
1.458,0.167 1.958,0.417 0.5,0.25 0.917,1.75 1.333,1.104 true 1.313,1 1,0.5 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.594,0.198 2.052,0.396 0.458,0.198 10 false F74 0.583,0.396 1.198,0.594 0.615,0.198 10 false CA2L 0.5,1.646 1.115,1.844 0.615,0.198 10 false CA2H
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-22 (CA2H) - F74-7 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR