Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2020.08
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Open in Bus 5 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the CAN main bus lines when the resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

CAN main bus lines or connector

·

Combination meter assembly

·

Central gateway ECU (network gateway ECU)

·

No. 3 CAN junction connector



This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.

WIRING DIAGRAM

C360952E06
0.698,0.969 1.469,1.167 0.771,0.198 10 false 120 Ω 1.365,0.604 2.135,0.802 0.771,0.198 10 false CA5H 1.375,1.146 2.146,1.344 0.771,0.198 10 false CA5L 1.813,0.604 2.083,0.771 0.271,0.167 10 false 15 1.823,1.135 2.094,1.302 0.271,0.167 10 false 16 2.49,1.135 2.76,1.302 0.271,0.167 10 false 17 2.552,0.594 2.823,0.76 0.271,0.167 10 false 6 4.521,0.573 4.792,0.74 0.271,0.167 10 false 1 4.521,1.125 4.792,1.292 0.271,0.167 10 false 12 2.646,1.646 3.083,1.896 0.438,0.25 10 false F114 2.646,1.802 4.646,2.135 2,0.333 10 false No. 3 CAN Junction Connector 5.167,1.781 7.094,2.115 1.927,0.333 10 false Combination Meter Assembly 5.177,1.635 5.615,1.885 0.438,0.25 10 false F4 5.417,0.604 6.188,0.802 0.771,0.198 10 false CANH 5.417,1.125 6.188,1.323 0.771,0.198 10 false CANL 6.083,0.969 6.854,1.167 0.771,0.198 10 false 120 Ω 0.365,1.802 2.302,2.188 1.938,0.385 10 false Central Gateway ECU (Network Gateway ECU) 0.375,1.646 0.813,1.896 0.438,0.25 10 false F74 5.177,1.135 5.448,1.302 0.271,0.167 10 false 31 5.167,0.583 5.438,0.75 0.271,0.167 10 false 32

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC maybe stored.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 3 CAN junction connector.


c.
C366166C04
1.417,0.833 1.917,1.083 0.5,0.25 0.625,2.5 0.917,2.021 true 0.646,1.146 0.917,1.75 true 1.75,1.75 2.271,1.104 true 1.76,2.021 2.26,2.5 true 0.417,0.5 0.729,0.698 0.313,0.198 10 false *a 1.51,0.875 2.125,1.073 0.615,0.198 10 false F114 0.094,1.01 1.01,1.208 0.917,0.198 10 false CANH*b 0.083,2.469 1,2.667 0.917,0.198 10 false CANL*b 2.333,1 3.25,1.198 0.917,0.198 10 false CANH*c 2.313,2.438 3.229,2.635 0.917,0.198 10 false CANL*c
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Combination Meter Assembly
*c to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F114-1 (CANH) - F114-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly
F114-6 (CANH) - F114-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to combination meter assembly) C



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

2.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 3 CAN JUNCTION CONNECTOR)

C

3.CHECK FOR OPEN IN CAN MAIN BUS LINES (COMBINATION METER ASSEMBLY - NO. 3 CAN JUNCTION CONNECTOR)
2.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 3 CAN JUNCTION CONNECTOR)
a.

Reconnect the F114 No. 3 CAN junction connector.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C367282C01
1.5,0.167 1.917,0.417 0.417,0.25 1.083,1.833 1.375,1.208 true 1.833,1.833 1.51,1.208 true 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 1.583,0.208 2.042,0.406 0.458,0.198 10 false F74 1.875,1.792 2.49,1.99 0.615,0.198 10 false CA5L 0.656,1.781 1.271,1.979 0.615,0.198 10 false CA5H
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-15 (CA5H) - F74-16 (CA5L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

B

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 3 CAN JUNCTION CONNECTOR)

3.CHECK FOR OPEN IN CAN MAIN BUS LINES (COMBINATION METER ASSEMBLY - NO. 3 CAN JUNCTION CONNECTOR)
a.

Reconnect the F114 No. 3 CAN junction connector.


b.

Disconnect the combination meter assembly connector.


c.
C328874C19
1.458,0.167 1.958,0.417 0.5,0.25 1.771,1.344 1.271,1.844 true 1.927,1.344 2.156,1.865 true 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 1.646,0.219 1.958,0.375 0.313,0.156 10 false F4 1.115,1.875 1.563,2.031 0.448,0.156 10 false CANL 1.979,1.885 2.427,2.042 0.448,0.156 10 false CANH
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-32 (CANH) - F4-31 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (COMBINATION METER ASSEMBLY - NO. 3 CAN JUNCTION CONNECTOR)