Home › Drivetrain › K313F (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2020.08
RM32H0E _52 Drivetrain _059618 K313F MULTIDRIVE / CVT _0300013 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K313F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P056014  System Voltage Circuit Short to Ground or Open  


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. The next time the engine is started, the ECM will illuminate the MIL and store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P056014 System Voltage Circuit Short to Ground or Open An open in the ECM backup power source circuit for 3 seconds (1 trip detection logic).
·

Open or short in backup power source circuit

·

Battery

·

Battery terminals

·

ECM


Comes on DTC stored SAE Code:
P0562

HINT:

If DTC P056014 is stored, the ECM will not store other DTCs or the data stored in the ECM will be partially cleared.


WIRING DIAGRAM

Refer to SFI system DTC P056014.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P056014

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

(a)

Turn the ignition switch to ON and wait for 3 seconds or more.




PROCEDURE

1.INSPECT BATTERY
a.

Inspect the battery.

Click herePower Source / Network>8NR-FTS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION

OK:

Battery voltage is between 11 and 14 V.



Result:
Proceed to
OK
NG



OK

2.CHECK BATTERY TERMINAL

NG

CHARGE OR REPLACE BATTERY

2.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

Click herePower Source / Network>8NR-FTS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION

OK:

Battery terminals are not loose or corroded.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF ECM)

NG

REPAIR OR REPLACE BATTERY TERMINAL

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF ECM)
a.
A354486C16
0.167,0.667 0.667,0.917 0.5,0.25 0.469,1.479 1.198,1.104 true 0.198,0.177 0.51,0.375 0.313,0.198 10 false *a 0.167,1.51 0.771,1.75 0.604,0.24 10 false 1 (BATT) 0.292,0.698 0.906,0.896 0.615,0.198 10 false A38
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-1 (BATT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P056014)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ECM)

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P056014)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Clear DTCs
50002 373

e.

Clear the DTCs.


f.

Turn the ignition switch off and wait for at least 30 seconds.


g.

Turn the ignition switch to ON.


h.

Turn the GTS on.


i.

Wait for 3 seconds or more.


j.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

k.

Read the DTCs.

Result:
Result Proceed to
DTC P056014 is output A
DTCs are not output B




A

5.REPLACE ECM

B

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT