Home › Drivetrain › K114 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2020.08
RM32H0E _52 Drivetrain _059616 K114 MULTIDRIVE / CVT _0292534 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K114 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0841  Transmission Fluid Pressure Sensor/Switch "A" Circuit Range/Performance  P2829  Pressure Control Solenoid "K" Performance or Stuck Off  


DESCRIPTION

The ECM controls the secondary oil pressure based on the secondary oil pressure signal output by the oil pressure sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0841 Transmission Fluid Pressure Sensor/Switch "A" Circuit Range/Performance Either one of the following conditions is met (1 trip detection logic):
·

When the requested oil pressure is 1.4 MPa (14.3 kgf/cm2, 203 psi) or more, the oil pressure sensor output is 0.5 MPa (5.1 kgf/cm2, 73 psi) or less for 2 seconds or more.

·

When the requested oil pressure is 1.0 MPa (10.2 kgf/cm2, 145 psi) or less, the difference between the calculated primary pulley pressure and target primary pulley pressure is 2.5 MPa (25.5 kgf/cm2, 363 psi) or more for 3 seconds or more.


·

Oil pressure sensor

·

ECM


Comes on DTC stored
P2829 Pressure Control Solenoid "K" Performance or Stuck Off One of the following conditions is met (1 trip detection logic):
·

When the requested oil pressure is 1.0 MPa (10.2 kgf/cm2, 145 psi) or less, the oil pressure sensor output is 2.5 MPa (25.5 kgf/cm2, 363 psi) or more for 3 seconds or more.

·

When the vehicle speed is less than 8 km/h (5 mph), the ratio of the transmission revolution sensor (NIN) output speed and transmission revolution sensor (NOUT) output speed exceeds a specified value for 0.2 seconds or more.

·

When the oil pressure sensor output is less than 0.283 MPa (2.9 kgf/cm2, 41 psi) and the target gear ratio is 2.0 or more, the actual gear ratio is less than 1.0 for 1.5 seconds or more.


·

Continuously variable transaxle assembly

·

ECM


Comes on DTC stored

DTC Detection Condition Patterns (P0841):
Vehicle Condition
Pattern 1 Pattern 2
Diagnostic Condition The requested oil pressure value is 1.4 MPa (14.3 kgf/cm2, 203 psi) or more. ○ -
The requested oil pressure value is 1.0 MPa (10.2 kgf/cm2, 145 psi) or less. - ○
Malfunction Condition The oil pressure sensor output value is 0.5 MPa (5.1 kgf/cm2, 73 psi) or less. ○ -
The difference between the calculated primary pulley pressure and target primary pulley pressure is 2.5 MPa (25.5 kgf/cm2, 363 psi) or more. - ○
Duration 2 seconds or more 3 seconds or more
Detection Logic 1 trip detection logic 1 trip detection logic

HINT:

This DTC is output when either of the above detection patterns is met.


DTC Detection Condition Patterns (P2829):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnostic Condition The requested oil pressure value is 1.0 MPa (10.2 kgf/cm2, 145 psi) or less. ○ - -
The vehicle speed is less than 8 km/h (5 mph). - ○ -
The oil pressure sensor output value is less than 0.283 MPa (2.9 kgf/cm2, 41 psi) and the target gear ratio is 2.0 or more. - - ○
Malfunction Condition The oil pressure sensor output value is 2.5 MPa (25.5 kgf/cm2, 363 psi) or more. ○ - -
The ratio of the transmission revolution sensor (NIN) output speed and transmission revolution sensor (NOUT) output speed exceeds a specified value. - ○ -
The actual gear ratio is less than 1.0. - - ○
Duration 3 seconds or more 0.2 seconds or more 1.5 seconds or more
Detection Logic 1 trip detection logic 1 trip detection logic 1 trip detection logic

HINT:

This DTC is output when any one of the above detection patterns is met.


MONITOR DESCRIPTION

The ECM checks for belt clamping high-pressure or low-pressure malfunctions. If a mechanical malfunction of the shift solenoid valve SLS or the oil pressure sensor is detected by the ECM, it illuminates the MIL and stores a DTC.

CAUTION / NOTICE / HINT

CAUTION:
·
C328174


·

Do not perform a stall test if there are any people or objects near the vehicle.

·

The vehicle could begin moving suddenly, resulting in a serious accident.


·
C328171


·

Do not perform a stall test if any wheel chocks are out of position.

·

The vehicle could begin moving suddenly, resulting in a serious accident.


·
C328173


·

Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.

·

The vehicle could begin moving suddenly, resulting in a serious accident.



NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0841 AND P2829)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs using the GTS.

HINT:

If any other DTCs besides P0841 or P2829 are output, perform troubleshooting for those DTCs first.



Result:
Result Proceed to
Both DTC P0841 and P2829 are output A
Only DTC P0841 is output B
Only DTC P2829 is output C
P0841 and/or P2829 and other DTCs are output D



A

2.READ VALUE USING GTS (A/T OIL PRESSURE)

B

12.READ VALUE USING GTS (A/T OIL PRESSURE)

C

19.READ VALUE USING GTS (A/T OIL PRESSURE)

D

2.READ VALUE USING GTS (A/T OIL PRESSURE)
CAUTION:
·

Do not perform a stall test if there are any people or objects near the vehicle.

·

Do not perform a stall test if any wheel chocks are out of position.

·

Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.



NOTICE:
·

This test must be performed after checking and confirming that the engine is normal.

·

Perform this test while the CVT fluid temperature is between 50 and 100°C (122 and 212°F).

·

Perform this test with the A/C off.

·

Do not perform the stall speed test for longer than 5 seconds.

·

When performing the stall speed test more than once, make sure to wait 15 seconds or more between tests.



a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.

Powertrain > Engine and ECT > Active Test
Tester Display
Connect the TC and TE1
50004 234 13

g.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
A/T Oil Pressure
50003 234 409

h.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Pressure Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
·

3.9 to 4.7 MPa (39.8 to 47.9 kgf/cm2, 566 to 682 psi): D position stall speed test

·

3.7 to 4.9 MPa (37.7 to 50.0 kgf/cm2, 537 to 711 psi): R position stall speed test


-

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

3.REPLACE ECM

B

4.REPLACE OIL PRESSURE SENSOR
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.REPLACE OIL PRESSURE SENSOR
a.

Replace the oil pressure sensor.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>OIL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234
Result:
Proceed to
NEXT




NEXT

6.PERFORM INITIALIZATION
6.PERFORM INITIALIZATION
NOTICE:
·

Performing Reset Memory will clear the learned value of the yaw rate and acceleration sensor (deceleration sensor zero point calibration) and the CVT oil pressure (CVT oil pressure calibration). Make sure to perform Reset Memory, yaw rate and acceleration sensor zero point calibration, and CVT oil pressure calibration when replacing any of the parts shown in the following table:

Replaced Part
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Airbag sensor assembly (Yaw rate and acceleration sensor)



·

After performing Reset Memory, always perform yaw rate and acceleration sensor (deceleration sensor zero point) calibration first, and then CVT oil pressure calibration.

·

Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).

·

Do not shake or vibrate the vehicle during calibration.



a.

Using the GTS, perform Reset Memory, deceleration sensor zero point calibration and CVT oil pressure calibration.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Perform a road test.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

f.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTC P0841 and/or P2829 is output A
DTCs are not output B



A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.PERFORM INITIALIZATION
9.PERFORM INITIALIZATION
NOTICE:
·

Performing Reset Memory will clear the learned value of the yaw rate and acceleration sensor (deceleration sensor zero point calibration) and the CVT oil pressure (CVT oil pressure calibration). Make sure to perform Reset Memory, yaw rate and acceleration sensor zero point calibration, and CVT oil pressure calibration when replacing any of the parts shown in the following table:

Replaced Part
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Airbag sensor assembly (Yaw rate and acceleration sensor)



·

After performing Reset Memory, always perform yaw rate and acceleration sensor (deceleration sensor zero point) calibration first, and then CVT oil pressure calibration.

·

Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).

·

Do not shake or vibrate the vehicle during calibration.



a.

Using the GTS, perform Reset Memory, deceleration sensor zero point calibration and CVT oil pressure calibration.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

10.CHECK DTC OUTPUT
10.CHECK DTC OUTPUT
a.

Perform a road test.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

f.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTC P2829 is output A
DTCs are not output B



A

11.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

B

END

11.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

Result:
Proceed to
NEXT



NEXT

12.READ VALUE USING GTS (A/T OIL PRESSURE)
CAUTION:
·

Do not perform a stall test if there are any people or objects near the vehicle.

·

Do not perform a stall test if any wheel chocks are out of position.

·

Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.



NOTICE:
·

This test must be performed after checking and confirming that the engine is normal.

·

Perform this test while the CVT fluid temperature is between 50 and 100°C (122 and 212°F).

·

Perform this test with the A/C off.

·

Do not perform the stall speed test for longer than 5 seconds.

·

When performing the stall speed test more than once, make sure to wait 15 seconds or more between tests.



a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.

Powertrain > Engine and ECT > Active Test
Tester Display
Connect the TC and TE1
50004 234 13

g.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
A/T Oil Pressure
50003 234 409

h.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Pressure Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
·

3.9 to 4.7 MPa (39.8 to 47.9 kgf/cm2, 566 to 682 psi): D position stall speed test

·

3.7 to 4.9 MPa (37.7 to 50.0 kgf/cm2, 537 to 711 psi): R position stall speed test


-

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

13.REPLACE ECM

B

14.REPLACE OIL PRESSURE SENSOR
13.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

14.REPLACE OIL PRESSURE SENSOR
a.

Replace the oil pressure sensor.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>OIL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
15.CLEAR DTC
a.

Clear the DTCs.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234
Result:
Proceed to
NEXT




NEXT

16.PERFORM INITIALIZATION
16.PERFORM INITIALIZATION
NOTICE:
·

Performing Reset Memory will clear the learned value of the yaw rate and acceleration sensor (deceleration sensor zero point calibration) and the CVT oil pressure (CVT oil pressure calibration). Make sure to perform Reset Memory, yaw rate and acceleration sensor zero point calibration, and CVT oil pressure calibration when replacing any of the parts shown in the following table:

Replaced Part
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Airbag sensor assembly (Yaw rate and acceleration sensor)



·

After performing Reset Memory, always perform yaw rate and acceleration sensor (deceleration sensor zero point) calibration first, and then CVT oil pressure calibration.

·

Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).

·

Do not shake or vibrate the vehicle during calibration.



a.

Using the GTS, perform Reset Memory, deceleration sensor zero point calibration and CVT oil pressure calibration.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

17.CHECK DTC OUTPUT
17.CHECK DTC OUTPUT
a.

Perform a road test.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

f.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTC P0841 is output A
DTCs are not output B



A

18.REPLACE ECM

B

END

18.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

19.READ VALUE USING GTS (A/T OIL PRESSURE)
CAUTION:
·

Do not perform a stall test if there are any people or objects near the vehicle.

·

Do not perform a stall test if any wheel chocks are out of position.

·

Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.



NOTICE:
·

This test must be performed after checking and confirming that the engine is normal.

·

Perform this test while the CVT fluid temperature is between 50 and 100°C (122 and 212°F).

·

Perform this test with the A/C off.

·

Do not perform the stall speed test for longer than 5 seconds.

·

When performing the stall speed test more than once, make sure to wait 15 seconds or more between tests.



a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.

Powertrain > Engine and ECT > Active Test
Tester Display
Connect the TC and TE1
50004 234 13

g.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
A/T Oil Pressure
50003 234 409

h.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Pressure Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
·

3.9 to 4.7 MPa (39.8 to 47.9 kgf/cm2, 566 to 682 psi): D position stall speed test

·

3.7 to 4.9 MPa (37.7 to 50.0 kgf/cm2, 537 to 711 psi): R position stall speed test


-

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

20.REPLACE ECM

B

21.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
20.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

21.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

Result:
Proceed to
NEXT



NEXT