The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear door lock with motor assembly removal/installation are shown below.
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal (for Audio and Visual System).
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal (for Navigation System (for Radio and Display Type)).
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for 8NR-FTS:
for 3ZR-FAE:
67498
3.REMOVE REAR DOOR REAR FRAME BRACKET
69284D
4.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG
84810
5.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL
67604
6.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
67628
7.REMOVE REAR DOOR TRIM BRACKET
67842E
8.REMOVE REAR DOOR SERVICE HOLE COVER
69240
9.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY
69227L
10.REMOVE REAR DOOR OUTSIDE HANDLE COVER
69060A
11.REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY
Disconnect the connector.
Using a T30 "TORX" socket wrench, remove the 3 screws and rear door lock with motor assembly.
When reusing the rear door lock with motor assembly:
Remove the door lock wiring harness seal from the rear door lock with motor assembly.
69740D
12.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
w/o Double Locking System:
| *a | Protective Tape |
|
Remove in this Direction |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw as shown in the illustration.
Disengage the guide to remove the rear door lock remote control cable assembly from the rear door lock with motor assembly.
w/ Double Locking System:
| *a | Protective Tape |
|
Remove in this Direction |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw as shown in the illustration.
Disengage the guide to remove the rear door lock remote control cable assembly from the rear door lock with motor assembly.
69780B
13.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY
w/o Double Locking System:
| *a | Protective Tape |
|
Remove in this Direction |
Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.
Disengage the guide to remove the rear door inside locking cable assembly from the rear door lock with motor assembly.
w/ Double Locking System:
| *a | Protective Tape |
|
Remove in this Direction |
Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.
Disengage the guide to remove the rear door inside locking cable assembly from the rear door lock with motor assembly.
69730E
14.REMOVE NO. 1 REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
| *a | Protective Tape |
|
Remove in this Direction |
Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.
Disengage the guide to remove the No. 1 rear door lock remote control cable assembly from the rear door lock with motor assembly.