Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY › from 2020.08
RM32H0E _58 Vehicle Interior _060065 SEAT BELT _0294235 FRONT SEAT OUTER BELT ASSEMBLY A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front seat outer belt assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)

CAUTION:
·
B458500

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Wear protective gloves. Sharp areas on the parts may injure your hands.



HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


CAUTION:
·
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If an SRS part is accidentally deployed, it may cause a serious injury.



Hide 67914 3.REMOVE FRONT DOOR SCUFF PLATE

Hide 62312B 4.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

a.

Disconnect the front door opening trim weatherstrip.


Hide 67918A 5.REMOVE REAR DOOR SCUFF PLATE

Hide 62332A 6.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

a.

Disconnect the rear door opening trim weatherstrip.


Hide 73233 7.REMOVE LAP BELT OUTER ANCHOR COVER

a.
B460521C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws and guide to remove the lap belt outer anchor cover as shown in the illustration.


Hide 73220 8.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY

a.
B458418

Remove the bolt to disconnect the floor anchor of the front seat outer belt assembly.


Hide 62414A 9.REMOVE CENTER PILLAR LOWER GARNISH

Hide 62420A 10.REMOVE CENTER PILLAR GARNISH ASSEMBLY

Hide 73220 11.REMOVE FRONT SEAT OUTER BELT ASSEMBLY

a.
B458419

Remove the nut to disconnect the shoulder anchor of the front seat outer belt assembly.


b.

for TMMT Made:

i.
B458420C01
1.052,0.323 1.281,0.458 true 0.625,0.979 0.875,0.781 true 1.323,0.438 1.635,0.635 0.313,0.198 10 false *a 0.458,0.948 0.771,1.146 0.313,0.198 10 false *b
*a Protective Tape
*b Locking Button


Using a screwdriver with its tip wrapped in protective tape, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.



c.

except TMMT Made:

i.
B460471C01
0.542,0.906 0.823,0.729 true 0.521,0.531 0.75,0.469 true 0.344,0.833 0.656,1.031 0.313,0.198 10 false *b 0.333,0.469 0.646,0.667 0.313,0.198 10 false *a
*a Protective Tape
*b Locking Button


Using a screwdriver with its tip wrapped in protective tape, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.



d.
B458421

Remove the bolt.


e.

Disengage the guides to remove the front seat outer belt assembly.


Hide 73200A 12.REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

a.
B458422

Remove the 2 bolts.


b.

Disengage the guide to remove the front shoulder belt anchor adjuster assembly.