Home › Drivetrain › K313F (MULTIDRIVE / CVT) › FRONT DIFFERENTIAL OIL SEAL (for RH Side) › from 2020.08
RM32H0E _52 Drivetrain _059618 K313F MULTIDRIVE / CVT _0292485 FRONT DIFFERENTIAL OIL SEAL(for RH Side) A

K313F MULTIDRIVE / CVT  FRONT DIFFERENTIAL OIL SEAL(for RH Side)  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front drive shaft oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link

*1: If the vehicle height has changed due to suspension or tire replacement

Disconnect cable from negative battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)
·

Air leaks from intake system

·

Gas leaks from exhaust system


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Front wheel alignment adjustment Perform the following procedures in the order shown:
1.

Clear zero point calibration data and store system information

2.

Perform yaw rate and acceleration sensor zero point calibration and store system information


·

VSC disabled or malfunctions

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.*1 Initialize headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)

CAUTION:
·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the transmission jack


Because the continuously variable transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the transmission jack could drop and components could fall down.


·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 36100 1.REMOVE TRANSFER ASSEMBLY

Hide 30400B 2.REMOVE CVT TYPE T OIL SEAL

a.
C155845C04
1.813,0.521 2.385,0.865 true 1.615,0.427 1.958,0.635 0.344,0.208 10 false *a
*a Protective Tape


Using a screwdriver with protective tape wound around the tip, pry out the CVT type T oil seal.

NOTICE:

Do not damage the continuously variable transaxle assembly.



Hide 43410M 3.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

C155846N10
1.021,0.74 1.385,0.99 false 2.719,2.177 3.135,2.688 true 0.75,0.677 1.135,0.865 0.385,0.188 10 false SST 2.448,2.115 2.833,2.302 0.385,0.188 10 false SST

a.

Using SST, remove the front drive shaft oil seal RH from the continuously variable transaxle assembly.

SST
09308-00010  

NOTICE:

Do not damage the continuously variable transaxle assembly.



Hide 43410M 4.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.

Coat the lip of a new front drive shaft oil seal RH with MP grease.


b.
C155847C04
1.542,1.094 1.667,1.604 1.667,1.604 1.177,1.281 true 1.573,1.646 1.948,1.885 0.375,0.24 10 false SST 3.052,0.469 3.333,0.656 0.281,0.188 10 true *a
*a -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


Using SST and a hammer, install the front drive shaft oil seal RH to the continuously variable transaxle assembly.

SST
09950-60010  (09951-00390)
09950-70010  (09951-07200)

Standard depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Make sure to install the front drive shaft oil seal RH as specified, otherwise malfunctions such as a fluid leak will occur.



Hide 30400B 5.INSTALL CVT TYPE T OIL SEAL

a.

Coat the lip of a new CVT type T oil seal with MP grease.


b.
C270342C03
0.5,0.344 0.677,0.531 false 2.031,1.281 2.469,1.646 true 0.229,0.26 0.635,0.469 0.406,0.208 10 false SST 2.521,1.583 2.927,1.771 0.406,0.188 10 false SST 0.104,1.573 0.333,1.76 0.229,0.188 10 true *a
*a 3.5 to 4.5 mm (0.138 to 0.177 in.)


Using SST and a hammer, install the CVT type T oil seal to the continuously variable transaxle assembly.

SST
09316-60011  (09316-00011)

Standard depth:

3.5 to 4.5 mm (0.138 to 0.177 in.)


NOTICE:
·

Be sure to install the CVT type T oil seal in the correct direction.

·

Make sure to install the CVT type T oil seal as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the CVT type T oil seal.




Hide 36100 6.INSTALL TRANSFER ASSEMBLY