Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2021.09
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0297889 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Distance Control Switch Circuit  


DESCRIPTION

The vehicle-to-vehicle distance control switch is used to set the distance for vehicle-to-vehicle distance control mode. The vehicle-to-vehicle distance control switch is installed in the steering pad switch assembly. The vehicle-to-vehicle distance set value can be changed by operating the vehicle-to-vehicle distance control switch while the dynamic radar cruise control system is controlling vehicle speed in vehicle-to-vehicle distance control mode.

WIRING DIAGRAM

for TMC Made:
C367152E14
1.344,0.75 2.875,0.99 1.531,0.24 10 false Distance Control Switch 0.917,2.646 2.885,2.938 1.969,0.292 10 false Steering Pad Switch Assembly 3.115,0.375 3.271,0.573 0.156,0.198 10 false 4 3.073,0.583 3.271,0.781 0.198,0.198 10 false z1 3.083,2.031 3.281,2.229 0.198,0.198 10 false z1 3.104,1.833 3.26,2.031 0.156,0.198 10 false 7 3.833,0.479 4.26,0.688 0.427,0.208 10 false DIST 3.833,1.927 4.26,2.135 0.427,0.208 10 false ECC 3.24,2.615 4.323,3.01 1.083,0.396 10 false Spiral Cable Sub-assembly 4.271,2.042 4.635,2.25 0.365,0.208 10 false F29 4.354,1.833 4.51,2.031 0.156,0.198 10 false 2 4.281,0.583 4.646,0.792 0.365,0.208 10 false F29 4.313,0.385 4.635,0.604 0.323,0.219 10 false 12 5.5,0.5 5.688,0.719 0.188,0.219 10 false 3 5.667,0.563 6.156,0.771 0.49,0.208 10 false LKSW 5.427,1.125 5.792,1.333 0.365,0.208 10 false R5 5.427,1.281 6.76,1.719 1.333,0.438 10 false Forward Recognition Camera 5.292,2.031 5.656,2.24 0.365,0.208 10 false A38 5.313,1.833 5.521,2.031 0.208,0.198 10 false 41 5.292,2.563 5.656,2.771 0.365,0.208 10 false C74 5.323,2.323 5.531,2.521 0.208,0.198 10 false 53 5.677,2.01 6.271,2.25 0.594,0.24 10 false ECSS 5.688,2.521 5.948,2.74 0.26,0.219 10 false E1 5.823,2.99 6.26,3.219 0.438,0.229 10 false ECM

for TMMT Made:
C367152E15
1.344,0.75 2.875,0.99 1.531,0.24 10 false Distance Control Switch 0.917,2.646 2.885,2.938 1.969,0.292 10 false Steering Pad Switch Assembly 3.115,0.375 3.271,0.573 0.156,0.198 10 false 4 3.073,0.583 3.271,0.781 0.198,0.198 10 false z1 3.083,2.031 3.281,2.229 0.198,0.198 10 false z1 3.104,1.833 3.26,2.031 0.156,0.198 10 false 7 3.833,0.479 4.26,0.688 0.427,0.208 10 false DIST 3.833,1.927 4.26,2.135 0.427,0.208 10 false ECC 3.24,2.615 4.323,3.01 1.083,0.396 10 false Spiral Cable Sub-assembly 4.271,2.042 4.635,2.25 0.365,0.208 10 false F29 4.354,1.833 4.51,2.031 0.156,0.198 10 false 2 4.281,0.583 4.646,0.792 0.365,0.208 10 false F29 4.313,0.385 4.635,0.604 0.323,0.219 10 false 12 5.5,0.5 5.688,0.719 0.188,0.219 10 false 3 5.667,0.563 6.156,0.771 0.49,0.208 10 false LKSW 5.427,1.125 5.792,1.333 0.365,0.208 10 false R5 5.427,1.281 6.76,1.719 1.333,0.438 10 false Forward Recognition Camera 5.292,2.031 5.656,2.24 0.365,0.208 10 false A38 5.313,1.833 5.521,2.031 0.208,0.198 10 false 41 5.292,2.531 5.656,2.74 0.365,0.208 10 false C62 5.323,2.323 5.531,2.521 0.208,0.198 10 false 53 5.677,2.01 6.271,2.25 0.594,0.24 10 false ECSS 5.688,2.521 5.948,2.74 0.26,0.219 10 false E1 5.823,2.99 6.26,3.219 0.438,0.229 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT




PROCEDURE

1.READ VALUE USING GTS (VEHICLE-TO-VEHICLE DISTANCE CONTROL SWITCH)
a.

Read the Data List according to the display on the GTS.

Powertrain > Radar Cruise2 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle-to-vehicle Distance Control Switch Vehicle-to-vehicle distance control switch signal ON or OFF ON: Vehicle-to-vehicle distance control switch pushed
OFF: Vehicle-to-vehicle distance control switch not pushed
-
Powertrain > Radar Cruise2 > Data List
Tester Display
Vehicle-to-vehicle Distance Control Switch
50003 426 4
OK:

The value of the Data List item changes according to the operation of the vehicle-to-vehicle distance control switch.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA AND BODY GROUND)
a.

Disconnect the F29 spiral cable sub-assembly connector.


b.

Disconnect the R5 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-12 (DIST) - R5-3 (LKSW) Always Below 1 Ω
F29-2 (ECC) - A38-41 (ECSS) Always Below 1 Ω
F29-12 (DIST) or R5-3 (LKSW) - Body ground Always 10 kΩ or higher
F29-2 (ECC) or A38-41 (ECSS) - Body ground Always 10 kΩ or higher



d.

Connect the R5 forward recognition camera connector.


e.

Connect the F29 spiral cable sub-assembly connector.


Result:
Proceed to
OK
NG



OK

5.CONFIRM MODEL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for TMC Made A
for TMMT Made B



A

6.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

B

7.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
6.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the C74 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-2 (ECC) or C74-53 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

7.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the C62 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-2 (ECC) or C62-53 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG