Home › Drivetrain › K313F (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2021.09
RM32H0E _52 Drivetrain _059618 K313F MULTIDRIVE / CVT _0300013 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K313F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P070513  Transmission Range Sensor "A" Circuit Open  P070562  Transmission Range Sensor "A" Signal Compare Failure  


DESCRIPTION

The park/neutral position switch and shift lock control unit assembly (transmission control switch) detect the shift lever position and send signals to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P070513 Transmission Range Sensor "A" Circuit Open When the ignition switch is ON and the battery voltage is 10.5 V or more, all signals are OFF simultaneously for NSW, P, R, N and D for 60 seconds (2 trip detection logic).
·

Wire harness or connector

·

Park/neutral position switch

·

Shift lock control unit assembly (Transmission control switch)

·

ECM


Comes on DTC stored SAE Code:
P0705
P070562 Transmission Range Sensor "A" Signal Compare Failure When the ignition switch is ON and the battery voltage is 10.5 V or more, either one of the following conditions is met (2 trip detection logic):
·

2 or more signals are ON simultaneously for 2 seconds or more for (NSW, P, N), R, D input signals.

·

When the S signal (M position switch signal) is ON, any of the NSW, P, R, N input signals is ON simultaneously for 2 seconds or more.


·

Wire harness or connector

·

Park/neutral position switch

·

Shift lock control unit assembly (Transmission control switch)

·

ECM


Comes on DTC stored SAE Code:
P0705

DTC Detection Condition Patterns (P070562):
Vehicle Condition
Pattern 1 Pattern 2
Diagnostic Condition Ignition switch ON and the battery voltage is 10.5 V or more ○ ○
Malfunction Condition 2 or more signals are ON simultaneously for (NSW, P, N), R, D input signals. ○ -
When the S signal (M position switch signal) is ON, any of the NSW, P, R, N input signals is ON simultaneously. - ○
Duration 2 seconds or more 2 seconds or more
Detection Logic 2 trip detection logic 2 trip detection logic

HINT:

This DTC is output when either of the above detection patterns is met.


MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch or the wire harness of the park/neutral position switch circuit.

The park/neutral position switch detects the shift lever position and sends a signal to the ECM. For safety, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

WIRING DIAGRAM

for TMMT Made
C356646E18
0.25,1.167 1.656,1.708 1.406,0.542 10 false from Certification ECU (Smart Key ECU Assembly)*1 0.25,2.063 1.677,2.5 1.427,0.438 10 false from Ignition or Starter Switch Assembly*2 0.802,3.052 1.583,3.25 0.781,0.198 10 false BKUP LP 2.51,1.302 2.667,1.5 0.156,0.198 10 false 4 2.76,1.302 2.917,1.5 0.156,0.198 10 false B 3.927,1.292 4.083,1.49 0.156,0.198 10 false L 4.188,1.281 4.344,1.479 0.156,0.198 10 false 9 3.865,1.99 4.177,2.188 0.313,0.198 10 false PL 4.188,1.99 4.344,2.188 0.156,0.198 10 false 3 3.875,2.531 4.188,2.729 0.313,0.198 10 false RL 4.188,2.531 4.344,2.729 0.156,0.198 10 false 2 3.885,3.083 4.198,3.281 0.313,0.198 10 false NL 4.188,3.083 4.344,3.281 0.156,0.198 10 false 8 3.865,3.615 4.177,3.813 0.313,0.198 10 false DL 4.198,3.604 4.354,3.802 0.156,0.198 10 false 7 2.75,2.802 3.063,3 0.313,0.198 10 false RB 2.375,4.125 2.833,4.323 0.458,0.198 10 false C36 2.365,4.271 4.448,4.521 2.083,0.25 10 false Park / Neutral Position Switch 2.427,5.292 2.885,5.49 0.458,0.198 10 false F17 2.417,5.448 4.448,5.771 2.031,0.323 10 false Shift Lock Control Unit Assembly (Transmission Control Switch) 4.5,6 7.031,6.24 2.531,0.24 10 false *1: w/ Entry and Start System 4.49,6.396 6.917,6.615 2.427,0.219 10 false *2: w/o Entry and Start System 5.958,5.635 6.417,5.833 0.458,0.198 10 false ECM 5.521,0.604 5.979,0.802 0.458,0.198 10 false NSW 5.51,1.271 5.969,1.469 0.458,0.198 10 false STA 5.531,1.99 5.688,2.188 0.156,0.198 10 false P 5.531,2.542 5.688,2.74 0.156,0.198 10 false R 5.521,3.063 5.677,3.26 0.156,0.198 10 false N 5.521,3.594 5.677,3.792 0.156,0.198 10 false D 5.521,4.844 5.677,5.042 0.156,0.198 10 false S 3.917,4.865 4.073,5.063 0.156,0.198 10 false S 2.75,4.854 3.063,5.052 0.313,0.198 10 false IG 4.177,4.833 4.333,5.031 0.156,0.198 10 false 5 2.51,4.802 2.667,5 0.156,0.198 10 false 4 5.188,0.542 5.5,0.74 0.313,0.198 10 false 57 5.188,1.219 5.5,1.417 0.313,0.198 10 false 29 5.188,1.906 5.5,2.104 0.313,0.198 10 false 64 5.188,2.469 5.5,2.667 0.313,0.198 10 false 35 5.188,2.99 5.5,3.188 0.313,0.198 10 false 65 5.188,3.521 5.5,3.719 0.313,0.198 10 false 34 5.188,4.771 5.5,4.969 0.313,0.198 10 false 59 5.125,0.708 5.583,0.906 0.458,0.198 10 false A38 5.125,4.969 5.583,5.167 0.458,0.198 10 false A38 5.125,1.385 5.583,1.583 0.458,0.198 10 false A38 5.135,2.104 5.594,2.302 0.458,0.198 10 false C62 5.125,2.646 5.583,2.844 0.458,0.198 10 false C62 5.125,3.167 5.583,3.365 0.458,0.198 10 false C62 5.125,3.708 5.583,3.906 0.458,0.198 10 false C62 0.771,5.135 1.938,5.344 1.167,0.208 10 false ECU-IG1 NO .1 2.49,2.802 2.646,3 0.156,0.198 10 false 1 0.167,0.167 3.417,0.417 3.25,0.25 12 false w/o Toyota Safety Sense:

for TMMT Made
C356646E19
0.25,1.167 1.656,1.708 1.406,0.542 10 false from Certification ECU (Smart Key ECU Assembly) 0.802,3.052 1.583,3.25 0.781,0.198 10 false BKUP LP 2.51,1.302 2.667,1.5 0.156,0.198 10 false 4 2.76,1.302 2.917,1.5 0.156,0.198 10 false B 3.927,1.292 4.083,1.49 0.156,0.198 10 false L 4.188,1.281 4.344,1.479 0.156,0.198 10 false 9 3.865,1.99 4.177,2.188 0.313,0.198 10 false PL 4.188,1.99 4.344,2.188 0.156,0.198 10 false 3 3.875,2.531 4.188,2.729 0.313,0.198 10 false RL 4.188,2.531 4.344,2.729 0.156,0.198 10 false 2 3.885,3.083 4.198,3.281 0.313,0.198 10 false NL 4.188,3.083 4.344,3.281 0.156,0.198 10 false 8 3.865,3.615 4.177,3.813 0.313,0.198 10 false DL 4.198,3.604 4.354,3.802 0.156,0.198 10 false 7 2.75,2.802 3.063,3 0.313,0.198 10 false RB 2.375,4.125 2.833,4.323 0.458,0.198 10 false C36 2.365,4.271 4.448,4.521 2.083,0.25 10 false Park / Neutral Position Switch 2.427,5.292 2.885,5.49 0.458,0.198 10 false F17 2.417,5.448 4.448,5.771 2.031,0.323 10 false Shift Lock Control Unit Assembly (Transmission Control Switch) 5.958,5.635 6.417,5.833 0.458,0.198 10 false ECM 5.521,0.604 5.979,0.802 0.458,0.198 10 false NSW 5.51,1.271 5.969,1.469 0.458,0.198 10 false STA 5.531,1.99 5.688,2.188 0.156,0.198 10 false P 5.531,2.542 5.688,2.74 0.156,0.198 10 false R 5.521,3.063 5.677,3.26 0.156,0.198 10 false N 5.521,3.594 5.677,3.792 0.156,0.198 10 false D 5.521,4.844 5.677,5.042 0.156,0.198 10 false S 3.917,4.865 4.073,5.063 0.156,0.198 10 false S 2.75,4.854 3.063,5.052 0.313,0.198 10 false IG 4.177,4.833 4.333,5.031 0.156,0.198 10 false 5 2.51,4.802 2.667,5 0.156,0.198 10 false 4 5.188,0.542 5.5,0.74 0.313,0.198 10 false 57 5.188,1.219 5.5,1.417 0.313,0.198 10 false 29 5.188,1.906 5.5,2.104 0.313,0.198 10 false 65 5.188,2.469 5.5,2.667 0.313,0.198 10 false 35 5.188,2.99 5.5,3.188 0.313,0.198 10 false 66 5.188,3.521 5.5,3.719 0.313,0.198 10 false 34 5.188,4.771 5.5,4.969 0.313,0.198 10 false 59 5.125,0.708 5.583,0.906 0.458,0.198 10 false A38 5.125,4.969 5.583,5.167 0.458,0.198 10 false A38 5.125,1.385 5.583,1.583 0.458,0.198 10 false A38 5.135,2.104 5.594,2.302 0.458,0.198 10 false C62 5.125,2.646 5.583,2.844 0.458,0.198 10 false C62 5.125,3.167 5.583,3.365 0.458,0.198 10 false C62 5.125,3.708 5.583,3.906 0.458,0.198 10 false C62 0.771,5.135 1.938,5.344 1.167,0.208 10 false ECU-IG1 NO .1 2.49,2.802 2.646,3 0.156,0.198 10 false 1 0.156,0.167 3.25,0.5 3.094,0.333 12 false w/ Toyota Safety Sense:

for TMC Made
C356646E27
0.25,1.167 1.656,1.708 1.406,0.542 10 false from Certification ECU (Smart Key ECU Assembly) 0.802,3.052 1.583,3.25 0.781,0.198 10 false BKUP LP 2.51,1.302 2.667,1.5 0.156,0.198 10 false 4 2.76,1.302 2.917,1.5 0.156,0.198 10 false B 3.927,1.292 4.083,1.49 0.156,0.198 10 false L 4.188,1.281 4.344,1.479 0.156,0.198 10 false 9 3.865,1.99 4.177,2.188 0.313,0.198 10 false PL 4.188,1.99 4.344,2.188 0.156,0.198 10 false 3 3.875,2.531 4.188,2.729 0.313,0.198 10 false RL 4.188,2.531 4.344,2.729 0.156,0.198 10 false 2 3.885,3.083 4.198,3.281 0.313,0.198 10 false NL 4.188,3.083 4.344,3.281 0.156,0.198 10 false 8 3.865,3.615 4.177,3.813 0.313,0.198 10 false DL 4.198,3.604 4.354,3.802 0.156,0.198 10 false 7 2.75,2.802 3.063,3 0.313,0.198 10 false RB 2.375,4.125 2.833,4.323 0.458,0.198 10 false C36 2.365,4.271 4.448,4.521 2.083,0.25 10 false Park / Neutral Position Switch 2.427,5.292 2.885,5.49 0.458,0.198 10 false F17 2.417,5.448 4.448,5.771 2.031,0.323 10 false Shift Lock Control Unit Assembly (Transmission Control Switch) 5.958,5.635 6.417,5.833 0.458,0.198 10 false ECM 5.521,0.604 5.979,0.802 0.458,0.198 10 false NSW 5.51,1.271 5.969,1.469 0.458,0.198 10 false STA 5.531,1.99 5.688,2.188 0.156,0.198 10 false P 5.531,2.542 5.688,2.74 0.156,0.198 10 false R 5.521,3.063 5.677,3.26 0.156,0.198 10 false N 5.521,3.594 5.677,3.792 0.156,0.198 10 false D 5.521,4.844 5.677,5.042 0.156,0.198 10 false S 3.917,4.865 4.073,5.063 0.156,0.198 10 false S 2.75,4.854 3.063,5.052 0.313,0.198 10 false IG 4.177,4.833 4.333,5.031 0.156,0.198 10 false 5 2.51,4.802 2.667,5 0.156,0.198 10 false 4 5.188,0.542 5.5,0.74 0.313,0.198 10 false 57 5.188,1.219 5.5,1.417 0.313,0.198 10 false 29 5.188,1.906 5.5,2.104 0.313,0.198 10 false 65 5.188,2.469 5.5,2.667 0.313,0.198 10 false 35 5.188,2.99 5.5,3.188 0.313,0.198 10 false 66 5.188,3.521 5.5,3.719 0.313,0.198 10 false 34 5.188,4.771 5.5,4.969 0.313,0.198 10 false 59 5.125,0.708 5.583,0.906 0.458,0.198 10 false A38 5.125,4.969 5.583,5.167 0.458,0.198 10 false A38 5.125,1.385 5.583,1.583 0.458,0.198 10 false A38 5.135,2.104 5.594,2.302 0.458,0.198 10 false C74 5.125,2.646 5.583,2.844 0.458,0.198 10 false C74 5.125,3.167 5.583,3.365 0.458,0.198 10 false C74 5.125,3.708 5.583,3.906 0.458,0.198 10 false C74 0.771,5.135 1.938,5.344 1.167,0.208 10 false ECU-IG1 NO .1 2.49,2.802 2.646,3 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON.

2.

Wait with the shift lever in each position (P, R, N and D) for 60 seconds or more each.

3.

Turn the ignition switch off.

4.

Perform steps (1) through (2) again.



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for TMMF Made A
for TMC Made B



A

2.READ VALUE USING GTS (NEUTRAL POSITION SW AND SHIFT SW STATUS)

B

7.READ VALUE USING GTS (NEUTRAL POSITION SW AND SHIFT SW STATUS)
2.READ VALUE USING GTS (NEUTRAL POSITION SW AND SHIFT SW STATUS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List.

Powertrain > Transmission > Data List
Tester Display
Neutral Position SW
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (D Range)
50003 373 20,15,14,13,28

e.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Position SW Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in P or N

·

ON: Shift lever in P or N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (P Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in P

·

ON: Shift lever in P


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (R Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in R

·

ON: Shift lever in R


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (N Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in N

·

ON: Shift lever in N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (D Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in D

·

ON: Shift lever in D


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

B

3.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
3.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
a.
C193930C61
0.083,1.083 0.583,1.333 0.5,0.25 1.677,1.063 2.167,0.417 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.208,1.125 0.604,1.375 0.396,0.25 10 false C36 2.219,0.302 2.531,0.469 0.313,0.167 10 false RB
*a Front view of wire harness connector
(to Park/Neutral Position Switch)


Disconnect the park/neutral position switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C36-1 (RB) - Body ground Ignition switch ON 11 to 14 V
C36-1 (RB) - Body ground Ignition switch off Below 1 V



c.

Connect the park/neutral position switch connector.


Result:
Proceed to
OK
NG



OK

4.INSPECT PARK/NEUTRAL POSITION SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)

4.INSPECT PARK/NEUTRAL POSITION SWITCH
a.
C193931C34
0.594,0.521 0.823,0.521 0.823,0.521 1.115,0.99 true 1,0.25 1.167,0.25 1.167,0.25 1.354,0.948 true 2.167,0.25 1.833,0.25 1.833,0.25 1.625,0.938 true 2.583,0.5 2.333,0.5 2.333,0.5 2.042,1 true 2.167,2 1.917,2 1.917,2 1.792,1.479 true 1.083,2 1.25,2 1.25,2 1.406,1.479 true 0.833,1.833 1.083,1.833 1.083,1.833 1.24,1.469 true 2.219,0.156 2.583,0.396 0.365,0.24 10 false RL 2.635,0.406 2.958,0.604 0.323,0.198 10 false RB 0.458,0.438 0.802,0.625 0.344,0.188 10 false B 0.708,1.75 1.177,1.938 0.469,0.188 10 false L 2.219,1.927 2.74,2.094 0.521,0.167 10 false DL 0.802,0.167 1.26,0.375 0.458,0.208 10 false PL 0.885,1.927 1.219,2.073 0.333,0.146 10 false NL 0.104,0.073 0.281,0.271 0.177,0.198 10 false *a
*a Component without harness connected
(Park/Neutral Position Switch)


Disconnect the C36 park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 9 (L) Shift lever in P or N Below 1 Ω
Shift lever not in P or N 10 kΩ or higher
1 (RB) - 3 (PL) Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher
1 (RB) - 2 (RL) Shift lever in R Below 1 Ω
Shift lever not in R 10 kΩ or higher
1 (RB) - 8 (NL) Shift lever in N Below 1 Ω
Shift lever not in N 10 kΩ or higher
1 (RB) - 7 (DL) Shift lever in D Below 1 Ω
Shift lever not in D 10 kΩ or higher



c.

Connect the C36 park/neutral position switch connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH A - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH A - ECM)
a.

Disconnect the C36 park/neutral position switch connector.


b.

Disconnect the A38 and C62 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (w/o Toyota Safety Sense):
Tester Connection Condition Specified Condition
C36-3 (PL) - C62-64 (P) Always Below 1 Ω
C36-2 (RL) - C62-35 (R) Always Below 1 Ω
C36-8 (NL) - C62-65 (N) Always Below 1 Ω
C36-7 (DL) - C62-34 (D) Always Below 1 Ω
C36-4 (B) - A38-57 (NSW) Always Below 1 Ω
C36-3 (PL) or C62-64 (P) - Body ground and other terminals Always 10 kΩ or higher
C36-2 (RL) or C62-35 (R) - Body ground and other terminals Always 10 kΩ or higher
C36-8 (NL) or C62-65 (N) - Body ground and other terminals Always 10 kΩ or higher
C36-7 (DL) or C62-34 (D) - Body ground and other terminals Always 10 kΩ or higher
C36-4 (B) or A38-57 (NSW) - Body ground and other terminals Always 10 kΩ or higher


Standard Resistance (w/ Toyota Safety Sense):
Tester Connection Condition Specified Condition
C36-3 (PL) - C62-65 (P) Always Below 1 Ω
C36-2 (RL) - C62-35 (R) Always Below 1 Ω
C36-8 (NL) - C62-66 (N) Always Below 1 Ω
C36-7 (DL) - C62-34 (D) Always Below 1 Ω
C36-4 (B) - A38-57 (NSW) Always Below 1 Ω
C36-3 (PL) or C62-65 (P) - Body ground and other terminals Always 10 kΩ or higher
C36-2 (RL) or C62-35 (R) - Body ground and other terminals Always 10 kΩ or higher
C36-8 (NL) or C62-66 (N) - Body ground and other terminals Always 10 kΩ or higher
C36-7 (DL) or C62-34 (D) - Body ground and other terminals Always 10 kΩ or higher
C36-4 (B) or A38-57 (NSW) - Body ground and other terminals Always 10 kΩ or higher



d.

Connect the A38 and C62 ECM connectors.


e.

Connect the C36 park/neutral position switch connector.


Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.READ VALUE USING GTS (NEUTRAL POSITION SW AND SHIFT SW STATUS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List.

Powertrain > Transmission > Data List
Tester Display
Neutral Position SW
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (D Range)
50003 373 20,15,14,13,28

e.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Position SW Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in P or N

·

ON: Shift lever in P or N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (P Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in P

·

ON: Shift lever in P


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (R Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in R

·

ON: Shift lever in R


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (N Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in N

·

ON: Shift lever in N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (D Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in D

·

ON: Shift lever in D


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

B

8.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
8.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
a.
C193930C61
0.083,1.083 0.583,1.333 0.5,0.25 1.677,1.063 2.167,0.417 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.208,1.125 0.604,1.375 0.396,0.25 10 false C36 2.219,0.302 2.531,0.469 0.313,0.167 10 false RB
*a Front view of wire harness connector
(to Park/Neutral Position Switch)


Disconnect the park/neutral position switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C36-1 (RB) - Body ground Ignition switch ON 11 to 14 V
C36-1 (RB) - Body ground Ignition switch off Below 1 V



c.

Connect the park/neutral position switch connector.


Result:
Proceed to
OK
NG



OK

9.INSPECT PARK/NEUTRAL POSITION SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)

9.INSPECT PARK/NEUTRAL POSITION SWITCH
a.
C193931C34
0.594,0.521 0.823,0.521 0.823,0.521 1.115,0.99 true 1,0.25 1.167,0.25 1.167,0.25 1.354,0.948 true 2.167,0.25 1.833,0.25 1.833,0.25 1.625,0.938 true 2.583,0.5 2.333,0.5 2.333,0.5 2.042,1 true 2.167,2 1.917,2 1.917,2 1.792,1.479 true 1.083,2 1.25,2 1.25,2 1.406,1.479 true 0.833,1.833 1.083,1.833 1.083,1.833 1.24,1.469 true 2.219,0.156 2.583,0.396 0.365,0.24 10 false RL 2.635,0.406 2.958,0.604 0.323,0.198 10 false RB 0.458,0.438 0.802,0.625 0.344,0.188 10 false B 0.708,1.75 1.177,1.938 0.469,0.188 10 false L 2.219,1.927 2.74,2.094 0.521,0.167 10 false DL 0.802,0.167 1.26,0.375 0.458,0.208 10 false PL 0.885,1.927 1.219,2.073 0.333,0.146 10 false NL 0.104,0.073 0.281,0.271 0.177,0.198 10 false *a
*a Component without harness connected
(Park/Neutral Position Switch)


Disconnect the C36 park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 9 (L) Shift lever in P or N Below 1 Ω
Shift lever not in P or N 10 kΩ or higher
1 (RB) - 3 (PL) Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher
1 (RB) - 2 (RL) Shift lever in R Below 1 Ω
Shift lever not in R 10 kΩ or higher
1 (RB) - 8 (NL) Shift lever in N Below 1 Ω
Shift lever not in N 10 kΩ or higher
1 (RB) - 7 (DL) Shift lever in D Below 1 Ω
Shift lever not in D 10 kΩ or higher



c.

Connect the C36 park/neutral position switch connector.


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH A - ECM)

NG

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH A - ECM)
a.

Disconnect the C36 park/neutral position switch connector.


b.

Disconnect the A38 and C74 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-3 (PL) - C74-65 (P) Always Below 1 Ω
C36-2 (RL) - C74-35 (R) Always Below 1 Ω
C36-8 (NL) - C74-66 (N) Always Below 1 Ω
C36-7 (DL) - C74-34 (D) Always Below 1 Ω
C36-4 (B) - A38-57 (NSW) Always Below 1 Ω
C36-3 (PL) or C74-65 (P) - Body ground and other terminals Always 10 kΩ or higher
C36-2 (RL) or C74-35 (R) - Body ground and other terminals Always 10 kΩ or higher
C36-8 (NL) or C74-66 (N) - Body ground and other terminals Always 10 kΩ or higher
C36-7 (DL) or C74-34 (D) - Body ground and other terminals Always 10 kΩ or higher
C36-4 (B) or A38-57 (NSW) - Body ground and other terminals Always 10 kΩ or higher



d.

Connect the A38 and C74 ECM connectors.


e.

Connect the C36 park/neutral position switch connector.


Result:
Proceed to
OK
NG



OK

11.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT