Home › Drivetrain › K313F (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2021.09
RM32H0E _52 Drivetrain _059618 K313F MULTIDRIVE / CVT _0300013 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K313F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P071512  Input/Turbine Speed Sensor "A" Circuit Short to Battery  P071514  Input/Turbine Speed Sensor "A" Circuit Short to Ground or Open  P071531  Input/Turbine Speed Sensor "A" No Signal  


DESCRIPTION

The ECM receives a signal from the transmission revolution sensor (NT) installed to the continuously variable transaxle to control the lock-up engagement pressure and forward and reverse clutch pressure.

The transmission revolution sensor (NT) detects the input turbine speed and sends a signal to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P071512 Input/Turbine Speed Sensor "A" Circuit Short to Battery There is no malfunction in transmission revolution sensor (NT) signals, and the transmission revolution sensor (NT) output voltage is higher than 1.8 V for 2 seconds (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly (Transmission revolution sensor (NT))

·

ECM


Comes on DTC stored SAE Code:
P07C0
P071514 Input/Turbine Speed Sensor "A" Circuit Short to Ground or Open There is no malfunction in transmission revolution sensor (NT) signals, and the transmission revolution sensor (NT) output voltage is less than 0.2 V for 2 seconds (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly (Transmission revolution sensor (NT))

·

ECM


Comes on DTC stored SAE Code:
P07BF
P071531 Input/Turbine Speed Sensor "A" No Signal All of the following conditions are met (1 trip detection logic):
·

Vehicle is driven with the shift lever in D

·

Output shaft speed is 300 rpm or more

·

No malfunctions are found in the park/neutral position switch

·

Input turbine speed indicated by the transmission revolution sensor (NT) is less than 300 rpm for 2 seconds


·

Wire harness or connector

·

Continuously variable transaxle assembly (Transmission revolution sensor (NT))

·

ECM


Comes on DTC stored SAE Code:
P0717

MONITOR DESCRIPTION

The transmission revolution sensor (NT) is used to detect the input turbine speed. The ECM determines the necessary gear ratio based on a comparison of the transmission revolution sensor (NT) (input turbine speed) and transmission revolution sensor (NOUT) (output shaft speed) signals.

When the output shaft speed is higher than the expected value and the input turbine speed is less than 300 rpm while driving with the shift lever in D, the ECM will determine that the transmission revolution sensor (NT) is malfunctioning, illuminate the MIL and store a DTC.

WIRING DIAGRAM

for TMMT Made
C319933E20
0.208,2.354 5.563,2.552 5.354,0.198 10 false Transmission Revolution Sensor (NT) 0.396,2.729 0.854,2.927 0.458,0.198 10 false C40 0.375,2.906 3.042,3.469 2.667,0.563 10 false Continuously Variable Transaxle Assembly (Transmission Wire) 6,2.885 6.458,3.083 0.458,0.198 10 false C62 6.01,3.042 6.469,3.24 0.458,0.198 10 false ECM 3.281,0.844 3.74,1.042 0.458,0.198 10 false NTB 3.271,2.063 3.729,2.26 0.458,0.198 10 false NTO 5.708,2.063 6.167,2.26 0.458,0.198 10 false NTO 5.708,0.844 6.167,1.042 0.458,0.198 10 false NTB 3.667,0.844 3.823,1.042 0.156,0.198 10 false 2 3.667,2.063 3.823,2.26 0.156,0.198 10 false 8 5.438,2.063 5.927,2.26 0.49,0.198 10 false 72 5.458,0.844 5.948,1.042 0.49,0.198 10 false 71 6.333,0.688 6.948,0.885 0.615,0.198 10 false 12 V 5.688,2.51 6.146,2.708 0.458,0.198 10 false E1 5.438,2.417 5.927,2.615 0.49,0.198 10 false 53

for TMC Made
C319933E24
0.208,2.354 5.563,2.552 5.354,0.198 10 false Transmission Revolution Sensor (NT) 0.396,2.729 0.854,2.927 0.458,0.198 10 false C40 0.375,2.906 3.052,3.479 2.677,0.573 10 false Continuously Variable Transaxle Assembly (Transmission Wire) 6,2.885 6.458,3.083 0.458,0.198 10 false C74 6.01,3.042 6.469,3.24 0.458,0.198 10 false ECM 3.281,0.844 3.74,1.042 0.458,0.198 10 false NTB 3.271,2.063 3.729,2.26 0.458,0.198 10 false NTO 5.708,2.063 6.167,2.26 0.458,0.198 10 false NTO 5.708,0.844 6.167,1.042 0.458,0.198 10 false NTB 3.667,0.844 3.823,1.042 0.156,0.198 10 false 2 3.667,2.063 3.823,2.26 0.156,0.198 10 false 8 5.438,2.063 5.927,2.26 0.49,0.198 10 false 72 5.458,0.844 5.948,1.042 0.49,0.198 10 false 71 6.333,0.688 6.948,0.885 0.615,0.198 10 false 12 V 5.688,2.51 6.146,2.708 0.458,0.198 10 false E1 5.438,2.417 5.927,2.615 0.49,0.198 10 false 53

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Drive the vehicle for 2 seconds or more at 7 km/h (4.375 mph) or more with the shift lever in D.



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for TMMF Made A
for TMC Made B



A

2.READ VALUE USING GTS (NT SENSOR SPEED AND NT SENSOR VOLTAGE)

B

8.READ VALUE USING GTS (NT SENSOR SPEED AND NT SENSOR VOLTAGE)
2.READ VALUE USING GTS (NT SENSOR SPEED AND NT SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List.

Powertrain > Transmission > Data List
Tester Display
NT Sensor Speed
NT Sensor Voltage
50003 373 174,175

e.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NT Sensor Speed Input turbine speed (NT) Min.: 0 rpm
Max.: 12750 rpm
·

Input turbine speed (NT) equal to engine speed (NE): Lock-up ON (After warming up engine)

·

Input turbine speed (NT) nearly equal to engine speed (NE): Lock-up OFF (Idling with shift lever in P or N)

·

0 rpm: Vehicle stopped with shift lever in R


Data is displayed in increments of 50 rpm.
NT Sensor Voltage Transmission revolution sensor (NT) output voltage Min.: 0.000 V
Max.: 4.999 V
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N) -

Result:
Result Proceed to
Data List value is not normal A
Data List value is normal B



A

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

B

7.REPLACE ECM
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the C40 transmission wire connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C40-8 (NTO) - C62-72 (NTO) Always Below 1 Ω
C40-2 (NTB) - C62-71 (NTB) Always Below 1 Ω
C62-53 (E1) - Body ground Always Below 1 Ω
C40-8 (NTO) or C62-72 (NTO) - Body ground and other terminals Always 10 kΩ or higher
C40-2 (NTB) or C62-71 (NTB) - Body ground and other terminals Always 10 kΩ or higher



d.

Connect the C62 ECM connector.


e.

Connect the C40 transmission wire connector.


Result:
Proceed to
OK
NG



OK

4.CHECK ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

4.CHECK ECM
a.
C265778C30
0.167,1.01 0.563,1.292 0.396,0.281 1.333,0.958 1.167,0.25 1.167,0.25 0.99,0.25 true 0.208,1.073 0.667,1.271 0.458,0.198 10 false C40 0.688,0.177 1.146,0.375 0.458,0.198 10 false NTB 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Transmission Wire)


Disconnect the transmission wire connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C40-2 (NTB) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Connect the transmission wire connector.


f.
C266347C22
1.438,1.802 1.24,1.802 1.24,1.802 1.052,1.083 true 2.583,1.792 2.385,1.792 2.385,1.792 2.208,1.125 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 2.625,1.708 3.25,1.896 0.625,0.188 10 false 72 (NTO) 1.479,1.719 2.031,1.906 0.552,0.188 10 false 53 (E1)
*a Component without harness connected
(ECM)


Disconnect the C62 ECM connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
72 (NTO) - 53 (E1) Always 99 to 101 Ω



Result:
Proceed to
OK
NG



OK

5.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

NG

6.REPLACE ECM
5.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

Result:
Proceed to
NEXT



NEXT

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.READ VALUE USING GTS (NT SENSOR SPEED AND NT SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List.

Powertrain > Transmission > Data List
Tester Display
NT Sensor Speed
NT Sensor Voltage
50003 373 174,175

e.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NT Sensor Speed Input turbine speed (NT) Min.: 0 rpm
Max.: 12750 rpm
·

Input turbine speed (NT) equal to engine speed (NE): Lock-up ON (After warming up engine)

·

Input turbine speed (NT) nearly equal to engine speed (NE): Lock-up OFF (Idling with shift lever in P or N)

·

0 rpm: Vehicle stopped with shift lever in R


Data is displayed in increments of 50 rpm.
NT Sensor Voltage Transmission revolution sensor (NT) output voltage Min.: 0.000 V
Max.: 4.999 V
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N) -

Result:
Result Proceed to
Data List value is not normal A
Data List value is normal B



A

9.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

B

13.REPLACE ECM
9.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the C40 transmission wire connector.


b.

Disconnect the C74 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C40-8 (NTO) - C74-72 (NTO) Always Below 1 Ω
C40-2 (NTB) - C74-71 (NTB) Always Below 1 Ω
C74-53 (E1) - Body ground Always Below 1 Ω
C40-8 (NTO) or C74-72 (NTO) - Body ground and other terminals Always 10 kΩ or higher
C40-2 (NTB) or C74-71 (NTB) - Body ground and other terminals Always 10 kΩ or higher



d.

Connect the C74 ECM connector.


e.

Connect the C40 transmission wire connector.


Result:
Proceed to
OK
NG



OK

10.CHECK ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

10.CHECK ECM
a.
C265778C30
0.167,1.01 0.563,1.292 0.396,0.281 1.333,0.958 1.167,0.25 1.167,0.25 0.99,0.25 true 0.208,1.073 0.667,1.271 0.458,0.198 10 false C40 0.688,0.177 1.146,0.375 0.458,0.198 10 false NTB 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Transmission Wire)


Disconnect the transmission wire connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C40-2 (NTB) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Connect the transmission wire connector.


f.
C266347C22
1.438,1.802 1.24,1.802 1.24,1.802 1.052,1.083 true 2.583,1.792 2.385,1.792 2.385,1.792 2.208,1.125 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 2.625,1.708 3.25,1.896 0.625,0.188 10 false 72 (NTO) 1.479,1.719 2.031,1.906 0.552,0.188 10 false 53 (E1)
*a Component without harness connected
(ECM)


Disconnect the C74 ECM connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
72 (NTO) - 53 (E1) Always 99 to 101 Ω



Result:
Proceed to
OK
NG



OK

11.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

NG

12.REPLACE ECM
11.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

Result:
Proceed to
NEXT



NEXT

12.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.REPLACE ECM

Result:
Proceed to
NEXT



NEXT