Home › Drivetrain › K313F (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2021.09
RM32H0E _52 Drivetrain _059618 K313F MULTIDRIVE / CVT _0300013 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K313F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P074011  Torque Converter Clutch Circuit Short to Ground  P074015  Torque Converter Clutch Circuit Short to Battery or Open  


DESCRIPTION

Based on the signal received by the shift solenoid valve SL, the ECM uses the shift solenoid valve SLU to control the lock-up clutch pressure.

If there is an open or short in the shift solenoid valve SL circuit, the ECM stops sending current to the malfunctioning shift solenoid valve.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P074011 Torque Converter Clutch Circuit Short to Ground While the lock-up is operating, a short is detected in the shift solenoid valve SL circuit 1 time or more consecutively (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly (Shift solenoid valve SL)

·

ECM


Comes on DTC stored SAE Code:
P2769
P074015 Torque Converter Clutch Circuit Short to Battery or Open While the lock-up is operating, an open is detected in the shift solenoid valve SL circuit 1 time or more consecutively (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly (Shift solenoid valve SL)

·

ECM


Comes on DTC stored SAE Code:
P2770

MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve SL circuit. If there is an open or short in the shift solenoid valve SL circuit, the ECM detects the malfunction, illuminates the MIL and stores a DTC.

WIRING DIAGRAM

for TMMF made
C319937E17
0.833,2.094 4.354,2.292 3.521,0.198 10 false Shift Solenoid Valve SL 0.625,2.563 1.083,2.76 0.458,0.198 10 false C40 0.625,2.729 4.74,3.146 4.115,0.417 10 false Continuously Variable Transaxle Assembly (Transmission Wire) 6.031,3.063 6.49,3.26 0.458,0.198 10 false ECM 5.615,1.844 5.99,2.156 0.375,0.313 10 false E1 5.604,0.896 6.063,1.094 0.458,0.198 10 false SL 5.365,0.896 5.823,1.094 0.458,0.198 10 false 75 5.354,1.74 5.813,1.938 0.458,0.198 10 false 53 4.49,0.906 4.948,1.104 0.458,0.198 10 false SL 4.75,0.906 5.208,1.104 0.458,0.198 10 false 3 6.031,2.917 6.49,3.115 0.458,0.198 10 false C62 6.198,0.615 6.813,0.813 0.615,0.198 10 false 12 V

for TMC Made
C319937E40
0.833,2.094 4.354,2.292 3.521,0.198 10 false Shift Solenoid Valve SL 0.625,2.563 1.083,2.76 0.458,0.198 10 false C40 0.625,2.729 4.74,3.146 4.115,0.417 10 false Continuously Variable Transaxle Assembly (Transmission Wire) 6.031,3.063 6.49,3.26 0.458,0.198 10 false ECM 5.615,1.844 5.99,2.156 0.375,0.313 10 false E1 5.604,0.896 6.063,1.094 0.458,0.198 10 false SL 5.365,0.896 5.823,1.094 0.458,0.198 10 false 75 5.354,1.74 5.813,1.938 0.458,0.198 10 false 53 4.49,0.906 4.948,1.104 0.458,0.198 10 false SL 4.75,0.906 5.208,1.104 0.458,0.198 10 false 3 6.031,2.917 6.49,3.115 0.458,0.198 10 false C74 6.198,0.615 6.813,0.813 0.615,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Drive the vehicle and confirm the lock-up on and off conditions according to Road Test.

Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for TMMF Made A
for TMC Made B



A

2.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL)

B

6.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL)
2.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL)
a.
C264597C09
2.063,0.885 2.365,0.406 2.365,0.406 2.521,0.406 true 0.198,0.219 0.51,0.417 0.313,0.198 10 *a 2.573,0.344 2.813,0.51 0.24,0.167 10 SL
*a Component without harness connected
(Transmission Wire)


Disconnect the C40 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (SL) - Body ground 20°C (68°F) 11 to 15 Ω



c.

Connect the C40 transmission wire connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

5.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C326700C28
1.427,0.198 1.813,0.427 0.385,0.229 1.146,1.719 1.323,1.021 true 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 0.896,1.76 1.656,1.979 0.76,0.219 10 false 75 (SL) 1.51,0.24 1.969,0.438 0.458,0.198 10 false C62
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C62-75 (SL) - Body ground 20°C (68°F) 11 to 15 Ω



c.

Connect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

Result:
Proceed to
NEXT



NEXT

6.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL)
a.
C264597C09
2.063,0.885 2.365,0.406 2.365,0.406 2.521,0.406 true 0.198,0.219 0.51,0.417 0.313,0.198 10 *a 2.573,0.344 2.813,0.51 0.24,0.167 10 SL
*a Component without harness connected
(Transmission Wire)


Disconnect the C40 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (SL) - Body ground 20°C (68°F) 11 to 15 Ω



c.

Connect the C40 transmission wire connector.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

9.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
7.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C326700C44
1.427,0.198 1.813,0.427 0.385,0.229 1.146,1.719 1.323,1.021 true 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 0.896,1.76 1.656,1.979 0.76,0.219 10 false 75 (SL) 1.49,0.229 1.948,0.427 0.458,0.198 10 false C74
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C74-75 (SL) - Body ground 20°C (68°F) 11 to 15 Ω



c.

Connect the ECM connector.


Result:
Proceed to
OK
NG



OK

8.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

Result:
Proceed to
NEXT



NEXT