The ECM performs learning control for the belt clamping pressure based on the belt clamping pressure signal, which is output by the oil pressure sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P084015 | Transmission Fluid Pressure Sensor/Switch "A" Circuit Short To Battery or Open | When 2 seconds or more have elapsed after engine start, there is an open or a short to +B in the oil pressure sensor circuit for 0.5 seconds (1 trip detection logic). | ·
Wire harness or connector ·
Oil pressure sensor ·
ECM |
Comes on | DTC stored | SAE Code:
P0843 |
This DTC indicates an open in the oil pressure sensor circuit. If there is an open or short in the oil pressure sensor circuit, the ECM detects the malfunction, illuminates the MIL and stores a DTC.
Refer to DTC P084011.
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>P084011
Do not perform a stall test if there are any people or objects near the vehicle.
The vehicle could begin moving suddenly, resulting in a serious accident.
Do not perform a stall test if any wheel chocks are out of position.
The vehicle could begin moving suddenly, resulting in a serious accident.
Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.
The vehicle could begin moving suddenly, resulting in a serious accident.
Perform initialization after replacing any parts related to the continuously variable transaxle system.
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Start the engine and wait for 2 seconds or more.
Check for DTCs again.
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for TMMF Made | A |
| for TMC Made | B |
A
B
A stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.
This test must be performed after checking and confirming that the engine is normal.
Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).
Perform this test with the air conditioning off.
Do not perform the stall speed test for longer than 5 seconds.
When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.
Perform this test with the AUTO function (shift-linked function) of the electric parking brake system off.
Warm up the engine.
Fully apply the parking brake and chock all 4 wheels.
When the parking brake indicator (red) is illuminated after the electric parking brake switch (electric parking brake switch assembly) has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch (electric parking brake switch assembly) is pulled to the lock side one more time.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Active Test / Activate the TC Terminal.
| Active Test Display |
|---|
| Activate the TC Terminal |
| Data List Display |
|---|
| Belt Clamping Force Sensor |
According to the display on the GTS, perform the Active Test.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Belt Clamping Force Sensor | Secondary oil pressure value | Min.: -64 MPa
Max.: 63.998 MPa |
Secondary oil pressure inspection:
·
3.5 to 5.5 MPa (35.6 to 56.1 kgf/cm2, 507 to 798 psi): D position stall test ·
3.6 to 5.5 MPa (36.7 to 56.1 kgf/cm2, 522 to 798 psi): R position stall test |
- |
| Result | Proceed to |
|---|---|
| Data List value is not normal | A |
| Data List value is normal | B |
A
B
Disconnect the C44 oil pressure sensor connector.
Disconnect the C62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C44-1 (E2) - C62-117 (EPTO) | Always | Below 1 Ω |
| C44-2 (PTO) - C62-86 (PTO) | Always | Below 1 Ω |
| C44-3 (VC) - C62-118 (VCPT) | Always | Below 1 Ω |
| C44-1 (E2) or C62-117 (EPTO) - Other terminals | Always | 10 kΩ or higher |
| C44-2 (PTO) or C62-86 (PTO) - Other terminals | Always | 10 kΩ or higher |
| C44-3 (VC) or C62-118 (VCPT) - Other terminals | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C62-86 (PTO) - Body ground | Ignition switch ON | Below 1 V |
| C44-2 (PTO) - Body ground | Ignition switch ON | Below 1 V |
Connect the C62 ECM connector.
Connect the C44 oil pressure sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Oil Pressure Sensor) |
Disconnect the oil pressure sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C44-3 (VC) - C44-1 (E2) | Ignition switch ON | 4.75 to 5.25 V |
Connect the oil pressure sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the oil pressure sensor.
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>OIL PRESSURE SENSOR>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
A stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.
This test must be performed after checking and confirming that the engine is normal.
Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).
Perform this test with the air conditioning off.
Do not perform the stall speed test for longer than 5 seconds.
When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.
Perform this test with the AUTO function (shift-linked function) of the electric parking brake system off.
Warm up the engine.
Fully apply the parking brake and chock all 4 wheels.
When the parking brake indicator (red) is illuminated after the electric parking brake switch (electric parking brake switch assembly) has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch (electric parking brake switch assembly) is pulled to the lock side one more time.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Active Test / Activate the TC Terminal.
| Active Test Display |
|---|
| Activate the TC Terminal |
| Data List Display |
|---|
| Belt Clamping Force Sensor |
According to the display on the GTS, perform the Active Test.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Belt Clamping Force Sensor | Secondary oil pressure value | Min.: -64 MPa
Max.: 63.998 MPa |
Secondary oil pressure inspection:
·
3.5 to 5.5 MPa (35.6 to 56.1 kgf/cm2, 507 to 798 psi): D position stall test ·
3.6 to 5.5 MPa (36.7 to 56.1 kgf/cm2, 522 to 798 psi): R position stall test |
- |
| Result | Proceed to |
|---|---|
| Data List value is not normal | A |
| Data List value is normal | B |
A
B
Disconnect the C44 oil pressure sensor connector.
Disconnect the C74 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C44-1 (E2) - C74-117 (EPTO) | Always | Below 1 Ω |
| C44-2 (PTO) - C74-86 (PTO) | Always | Below 1 Ω |
| C44-3 (VC) - C74-118 (VCPT) | Always | Below 1 Ω |
| C44-1 (E2) or C74-117 (EPTO) - Other terminals | Always | 10 kΩ or higher |
| C44-2 (PTO) or C74-86 (PTO) - Other terminals | Always | 10 kΩ or higher |
| C44-3 (VC) or C74-118 (VCPT) - Other terminals | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C74-86 (PTO) - Body ground | Ignition switch ON | Below 1 V |
| C44-2 (PTO) - Body ground | Ignition switch ON | Below 1 V |
Connect the C74 ECM connector.
Connect the C44 oil pressure sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Oil Pressure Sensor) |
Disconnect the oil pressure sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C44-3 (VC) - C44-1 (E2) | Ignition switch ON | 4.75 to 5.25 V |
Connect the oil pressure sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the oil pressure sensor.
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>OIL PRESSURE SENSOR>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT