Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › from 2021.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P007A11  Charge Air Cooler Temperature Sensor Bank 1 Circuit Short to Ground  


DESCRIPTION

A283580E01
3.354,2.271 3.74,1.99 false 2.26,0.406 2.833,0.667 0.573,0.26 10 Fig. 1: 3.292,4.271 4.167,4.5 0.875,0.229 10 Temperature 2.396,0.969 2.771,1.219 0.375,0.25 10 (kΩ) 2.281,1.146 2.521,1.365 0.24,0.219 10 30 2.281,1.583 2.521,1.802 0.24,0.219 10 10 2.354,1.875 2.594,2.094 0.24,0.219 10 5 2.354,2.094 2.594,2.313 0.24,0.219 10 3 2.354,2.26 2.51,2.479 0.156,0.219 10 2 2.344,2.531 2.594,2.75 0.25,0.219 10 1 2.24,2.833 2.479,3.052 0.24,0.219 10 0.5 2.24,3.198 2.479,3.417 0.24,0.219 10 0.2 2.24,3.469 2.479,3.688 0.24,0.219 10 0.1 2.281,1.323 2.531,1.542 0.25,0.219 10 20 2.542,3.823 2.781,4.042 0.24,0.219 10 -20 2.938,3.823 3.177,4.042 0.24,0.219 10 0 3.208,3.823 3.448,4.042 0.24,0.219 10 20 3.521,3.823 3.76,4.042 0.24,0.219 10 40 3.833,3.823 4.073,4.042 0.24,0.219 10 60 4.146,3.823 4.385,4.042 0.24,0.219 10 80 4.385,3.823 4.625,4.042 0.24,0.219 10 100 2.583,4 2.823,4.219 0.24,0.219 10 -4 2.896,4 3.135,4.219 0.24,0.219 10 32 3.208,4 3.448,4.219 0.24,0.219 10 68 3.479,4 3.729,4.25 0.25,0.25 10 104 3.792,4 4.125,4.25 0.333,0.25 10 140 4.094,4 4.417,4.25 0.323,0.25 10 176 4.385,4 4.708,4.25 0.323,0.25 10 212 4.677,3.823 5,4.073 0.323,0.25 10 (°C) 4.677,4 5,4.25 0.323,0.25 10 (°F) 3.802,1.896 4.583,2.167 0.781,0.271 10 Acceptable 2.26,0.719 3.083,0.917 0.823,0.198 10 Resistance 2.24,3.021 2.479,3.24 0.24,0.219 10 0.3

The intake air temperature sensor, built into the No. 2 turbo pressure sensor, monitors the intake air temperature for intake manifold. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (See Fig. 1).

The intake air temperature sensor is powered by a 5 V supply from terminal THIM of the ECM, via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes, according to changes in the intake air temperature, the voltage at terminal THIM also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

HINT:

When DTC P007A11 is stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 45°C (113°F) by the ECM. Fail-safe mode continues until a pass condition is detected.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P007A11 Charge Air Cooler Temperature Sensor Bank 1 Circuit Short to Ground The intake air temperature sensor output voltage is less than 0.1 V for 3 seconds or more (1 trip detection logic).
·

Short in intake air temperature sensor (No. 2 turbo pressure sensor) circuit

·

No. 2 turbo pressure sensor (intake air temperature sensor)

·

ECM


Does not come on DTC stored SAE Code: P007C

HINT:

When this DTC is output, check the intake air temperature (for intake manifold) in the Data List. Enter the following menus: Powertrain / Engine / Data List / All Data / Intake Air Temperature B1S1 (Turbo).

DTC No. Intake Air Temperature B1S1 (Turbo) Malfunction
P007A11 140°C (284°F) Short in THIM circuit to ground

If the Data List values is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the intake air temperature. When the intake air temperature sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the intake air temperature sensor circuit and stores this DTC.

Example:

If the intake air temperature sensor output voltage is less than 0.1 V for 3 seconds or more, the ECM store this DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P007A11.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A346389E09
0.271,2.729 0.729,2.927 0.458,0.198 10 false C39 0.271,2.906 2.167,3.385 1.896,0.479 10 false Intake Air Temperature Sensor (No. 2 Turbo Pressure Sensor) 1.99,1.448 2.448,1.646 0.458,0.198 10 false 4 1.979,2.052 2.438,2.25 0.458,0.198 10 false 2 1.583,1.479 2.042,1.677 0.458,0.198 10 false THIM 1.719,2.083 2.177,2.281 0.458,0.198 10 false E2 5.594,3.115 6.708,3.417 1.115,0.302 10 false C62*1, C74*2 5.865,3.271 6.271,3.573 0.406,0.302 10 false ECM 5.094,2.063 5.552,2.26 0.458,0.198 10 false 137 5.396,2.063 5.854,2.26 0.458,0.198 10 false EPIM 5.094,1.49 5.552,1.688 0.458,0.198 10 false 107 5.385,1.479 5.844,1.677 0.458,0.198 10 false THIM 6.01,1 6.469,1.198 0.458,0.198 10 false 5 V 5.969,1.365 6.427,1.563 0.458,0.198 10 false R 2.958,3.031 4.99,3.323 2.031,0.292 10 false *1: for TMMT Made 2.979,3.365 5.01,3.656 2.031,0.292 10 false *2: for TMC Made

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
A226261C31
0.823,1.74 1.5,2.063 0.677,0.323 10 false *1 2.646,1.74 3.167,1.896 0.521,0.156 10 false *2 2.406,0.917 2.844,1.146 0.438,0.229 10 false THIM 2.438,1.448 2.948,1.698 0.51,0.25 10 false EPIM 0.99,0.906 1.51,1.188 0.521,0.281 10 false THIM 1.135,1.271 1.479,1.521 0.344,0.25 10 false E2
*1 No. 2 turbo pressure sensor
*2 ECM


a.

Disconnect the No. 2 turbo pressure sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / All Data / Intake Air Temperature B1S1 (Turbo).

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature B1S1 (Turbo)
50003 372 310

f.

According to the display on the GTS, read the Data List.

Standard Value:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (NO. 2 TURBO PRESSURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (NO. 2 TURBO PRESSURE SENSOR - ECM)
a.

Disconnect the C39 No. 2 turbo pressure sensor connector.


b.

Disconnect the C62*1 or C74*2 ECM connector.

*1: for TMMT Made

*2: for TMC Made



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for TMMT Made
Tester Connection Condition Specified Condition
C39-4 (THIM) or C62-107 (THIM) - Body ground and other terminals Always 10 kΩ or higher

for TMC Made
Tester Connection Condition Specified Condition
C39-4 (THIM) or C74-107 (THIM) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR