Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › from 2021.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P010012  Mass or Volume Air Flow Sensor "A" Circuit Short to Battery  


DESCRIPTION

The mass air flow meter is a sensor that measures the intake air volume. The ECM uses this information to determine the ignition timing and fuel injection duration necessary for an optimal air fuel ratio. Inside the mass air flow meter are a hot wire element and a cold wire element which are exposed to the flow of intake air. The bridge circuit shown in the illustration outputs voltage to transmit information regarding heat loss of the hot wire element caused by air flow. Depending on the air flow, this voltage will change between approximately 0.2 V and 4.9 V. Based on this voltage, the ECM calculates the air flow to determine the ignition timing and fuel injection duration necessary for an optimal air fuel ratio.

HINT:

When P010012 is stored, the ECM enters fail-safe mode. During fail-safe mode, boost prohibited and the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.


A160257E12
1.969,1.938 2.427,1.51 2.427,1.51 2.573,1.51 false 5.406,1.99 5.021,2.771 5.021,2.771 4.896,2.771 true 5.781,2 5.281,3.063 5.281,3.063 5.156,3.063 true 6.302,2.031 5.854,3.354 5.854,3.354 5.188,3.354 true 1.594,1.927 1.313,1 1.313,1 1.229,1 true 4.375,0.865 4.833,0.438 4.833,0.438 4.979,0.438 false 1.667,0.531 2.583,1.021 0.917,0.49 10 false +B 0.042,0.938 1.542,1.438 1.5,0.5 10 false Cold Wire Element 2.625,1.438 4.083,1.75 1.458,0.313 10 false Hot Wire Element 2.573,2.031 3.74,2.281 1.167,0.25 10 false Output Voltage 2.802,2.677 4.938,3.042 2.135,0.365 10 false Temperature Sensor (Thermistor) 4.063,3.292 5.396,3.594 1.333,0.302 10 false Hot Wire Element 3.969,2.979 5.167,3.198 1.198,0.219 10 false Cold Wire Element 1.938,1.042 3.323,1.271 1.385,0.229 10 false Power Transistor 5.052,0.375 6.365,0.958 1.313,0.583 10 false Mass Air Flow Meter

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P010012 Mass or Volume Air Flow Sensor "A" Circuit Short to Battery The mass air flow meter voltage is higher than 4.9 V for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored SAE Code: P0103

HINT:

When this DTC is output, check the mass air flow in the Data List. Enter the following menus: Powertrain / Engine / Data List / All Data / Mass Air Flow Sensor.

DTC No. Mass Air Flow Sensor Malfunction
P010012 271.0 gm/sec or more
·

Short in VG circuit to power source circuit

·

Open in E2G circuit



If the Data List values is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

If there is a defect or an open or short circuit in the mass air flow meter, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter circuit and stores this DTC.

Example:

When the sensor output voltage remains higher than 4.9 V for 3 seconds or more, the ECM stores this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P010012.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A384822E10
0.49,2.875 1.563,3.073 1.073,0.198 10 false Battery 3.552,0.823 3.823,1.01 0.271,0.188 10 false +B 4.75,1.135 5.021,1.323 0.271,0.188 10 false VG 4.688,1.646 5.073,1.833 0.385,0.188 10 false E2G 6.052,1.125 6.323,1.313 0.271,0.188 10 false VG 6.052,1.625 6.438,1.813 0.385,0.188 10 false E2G 6.052,2.906 6.521,3.094 0.469,0.188 10 false MREL 6.323,4.031 6.792,4.219 0.469,0.188 10 false ECM 3.594,2.146 3.938,2.354 0.344,0.208 10 false C6 5.656,1.24 6.01,1.427 0.354,0.188 10 false C62 5.688,1.01 6.042,1.198 0.354,0.188 10 false 92 5.688,1.521 6.042,1.708 0.354,0.188 10 false 91 5.656,1.74 6.01,1.927 0.354,0.188 10 false C62 5.656,3 6.01,3.188 0.354,0.188 10 false A38 5.698,2.802 6.052,2.99 0.354,0.188 10 false 46 5.042,1.146 5.396,1.333 0.354,0.188 10 false 3 5.052,1.646 5.406,1.833 0.354,0.188 10 false 2 3.385,0.823 3.656,1.01 0.271,0.188 10 false 1 3.604,2.323 5.094,2.594 1.49,0.271 10 false Mass Air Flow Meter 2.646,1.063 3.406,1.229 0.76,0.167 10 false EFI NO. 3 0.438,1.063 1.438,1.375 1,0.313 10 false EFI-MAIN NO. 1 1.688,2 2.469,2.25 0.781,0.25 10 false EFI-MAIN 0.354,1.76 1.333,1.969 0.979,0.208 10 false BATT MAIN 1.438,1.552 1.729,1.75 0.292,0.198 10 false 5 2.479,1.521 2.823,1.719 0.344,0.198 10 false 6 2.448,0.854 2.604,1.052 0.156,0.198 10 false 4 1.469,0.844 1.625,1.042 0.156,0.198 10 false 3 1.521,2.375 2.302,2.625 0.781,0.25 10 false 1B 1.531,2.542 2.563,2.927 1.031,0.385 10 false No. 1 Integration Relay 0.156,0.125 2.781,0.5 2.625,0.375 12 false for TMMT Made:

A384822E09
0.49,2.875 1.563,3.073 1.073,0.198 10 false Battery 3.552,0.823 3.823,1.01 0.271,0.188 10 false +B 4.75,1.135 5.021,1.323 0.271,0.188 10 false VG 4.688,1.646 5.073,1.833 0.385,0.188 10 false E2G 6.052,1.125 6.323,1.313 0.271,0.188 10 false VG 6.052,1.625 6.438,1.813 0.385,0.188 10 false E2G 6.052,2.906 6.521,3.094 0.469,0.188 10 false MREL 6.323,4.031 6.792,4.219 0.469,0.188 10 false ECM 3.594,2.146 3.938,2.354 0.344,0.208 10 false C6 5.656,1.24 6.01,1.427 0.354,0.188 10 false C74 5.688,1.01 6.042,1.198 0.354,0.188 10 false 92 5.688,1.521 6.042,1.708 0.354,0.188 10 false 91 5.656,1.74 6.01,1.927 0.354,0.188 10 false C74 5.656,3 6.01,3.188 0.354,0.188 10 false A38 5.698,2.802 6.052,2.99 0.354,0.188 10 false 46 5.042,1.146 5.396,1.333 0.354,0.188 10 false 3 5.052,1.646 5.406,1.833 0.354,0.188 10 false 2 3.385,0.823 3.656,1.01 0.271,0.188 10 false 1 3.604,2.323 5.094,2.594 1.49,0.271 10 false Mass Air Flow Meter 2.646,1.063 3.406,1.229 0.76,0.167 10 false EFI NO. 3 0.438,1.063 1.438,1.375 1,0.313 10 false EFI-MAIN NO. 1 1.688,2 2.469,2.25 0.781,0.25 10 false EFI-MAIN 0.354,1.76 1.333,1.969 0.979,0.208 10 false BATT MAIN 2.458,1.542 2.75,1.74 0.292,0.198 10 false 5 1.417,1.542 1.76,1.74 0.344,0.198 10 false 6 2.448,0.854 2.604,1.052 0.156,0.198 10 false 4 1.469,0.844 1.625,1.042 0.156,0.198 10 false 3 1.521,2.375 2.302,2.625 0.781,0.25 10 false 1B 1.531,2.542 2.563,2.927 1.031,0.385 10 false No. 1 Integration Relay 0.156,0.146 2.677,0.563 2.521,0.417 12 false for TMC Made:

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the C6 mass air flow meter connector.


b.

Disconnect the C62*1 or C74*2 ECM connector.

*1: for TMMT Made

*2: for TMC Made



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for TMMT Made
Tester Connection Condition Specified Condition
C6-2 (E2G) - C62-91 (E2G) Always Below 1 Ω
C6-3 (VG) or C62-92 (VG) - Body ground and other terminals Always 10 kΩ or higher

for TMC Made
Tester Connection Condition Specified Condition
C6-2 (E2G) - C74-91 (E2G) Always Below 1 Ω
C6-3 (VG) or C74-92 (VG) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.

Disconnect the C6 mass air flow meter connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C6-2 (E2G) - Body ground Always Below 1 Ω


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG