Refer to DTC P023511.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P023511
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P023515 | Turbocharger/Supercharger Boost Sensor "A" Circuit Short to Battery or Open | The No. 1 turbo pressure sensor output voltage is higher than 4.63 V for 3 seconds or more (1 trip detection logic). | ·
Open or short in No. 1 turbo pressure sensor circuit ·
No. 1 turbo pressure sensor ·
ECM |
Comes on | DTC stored | SAE Code: P0238 |
When this DTC is output, check the No. 1 turbo pressure sensor in the Data List. Enter the following menus: Powertrain / Engine / Data List / All Data / Boost Pressure Sensor.
| DTC No. | Boost Pressure Sensor | Malfunction |
|---|---|---|
| P023515 | Approximately 310 kPa [45 psi] or higher | ·
Short in VPTA to PTA circuit ·
Open in PTA circuit ·
Open in EPTA circuit |
If the Data List values is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.
The ECM monitors the No. 1 turbo pressure sensor voltage and uses this value to calculate the intercooler internal pressure. When the No. 1 turbo pressure sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the No. 1 turbo pressure sensor circuit and stores this DTC.
Example:
If the No. 1 turbo pressure sensor output voltage is higher than 4.63 V for 3 seconds or more, the ECM store this DTC
| Required Sensors/Components | No. 1 turbo pressure sensor |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and wait 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P023515.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Refer to DTC P023511.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P023511
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| *a | Front view of wire harness connector
(to No. 1 Turbo Pressure Sensor) |
Disconnect the No. 1 turbo pressure sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C3-3 (VC) - C3-2 (E2) | Ignition switch ON | 4.75 to 5.25 V |
| C3-1 (PIM) - C3-2 (E2) | Ignition switch ON | 3.0 to 5.25 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 1 turbo pressure sensor.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTC.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| P023515 is output | B |
A
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
B
Disconnect the C3 No. 1 turbo pressure sensor connector.
Disconnect the C62*1 or C74*2 ECM connector.
*1: for TMMT Made
*2: for TMC Made
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C3-1 (PIM) - C62-108 (PTA) | Always | Below 1 Ω |
| C3-2 (E2) - C62-139 (EPTA) | Always | Below 1 Ω |
| C3-1 (PIM) or C62-108 (PTA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C3-1 (PIM) - C74-108 (PTA) | Always | Below 1 Ω |
| C3-2 (E2) - C74-139 (EPTA) | Always | Below 1 Ω |
| C3-1 (PIM) or C74-108 (PTA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG