Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › from 2021.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P123513  High Pressure Fuel Pump Circuit Open  


DESCRIPTION

The high-pressure direct injection fuel system consists of a spill control valve, check valve, fuel relief valve, fuel pressure sensor, fuel pump assembly (for high pressure side) and fuel injector assemblies. The spill control valve adjusts the return volume of the high-pressure fuel. The check valve mechanically opens and closes the paths to the fuel delivery pipes. The relief valve releases the fuel back to the fuel tank if the high-pressure fuel system malfunctions. The fuel pump assembly (for high pressure side) is installed to the cylinder head cover and operated by a cam installed to the end of the exhaust camshaft. Rotation of the camshaft moves the pump plunger inside the fuel pump assembly (for high pressure side) up and down, pressurizing the fuel. The pressurized fuel opens the check valve and is pumped into the fuel delivery pipe.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P123513 High Pressure Fuel Pump Circuit Open Open or short in fuel pump (for high pressure side) circuit detected 60 times or more (1 trip detection logic).
·

Open or short in fuel pump assembly (for high pressure side) circuit

·

Fuel pump assembly (for high pressure side)

·

ECM


Comes on DTC stored SAE Code:
P1235

MONITOR DESCRIPTION

If an open or short in the fuel pump (for high pressure side) circuit is detected after the engine is started, the ECM will illuminate the MIL and store this DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Fuel pump assembly (for high pressure side)
Required Sensors/Components (Related) ECM
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine.

9.

Idle the engine for 10 seconds or more [A].

10.

Enter the following menus: Powertrain / Engine / Trouble Codes [B].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P123513.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.




WIRING DIAGRAM

A384830E09
1.854,0.844 2.01,1.042 0.156,0.198 10 false 2 1.854,1.5 2.01,1.698 0.156,0.198 10 false 1 0.427,2.25 2,2.677 1.573,0.427 10 false Fuel Pump assembly (for High Pressure Side) 3.542,2 3.698,2.198 0.156,0.198 10 false * 5.292,1.625 5.698,1.844 0.406,0.219 10 false FP1- 5.292,0.958 5.74,1.177 0.448,0.219 10 false FP1+ 5.667,2.385 6.073,2.604 0.406,0.219 10 false ECM 2.667,2.427 3.396,2.719 0.729,0.292 10 false *: Shielded 0.417,2.031 1.365,2.25 0.948,0.219 10 false C55 5.427,2.198 6.375,2.594 0.948,0.396 10 false C62*1, C74*2 5,1.49 5.406,1.708 0.406,0.219 10 false 29 5,0.823 5.406,1.042 0.406,0.219 10 false 28 3.948,2.417 5.573,2.698 1.625,0.281 10 false *2: for TMC Made 3.958,2.094 5.583,2.375 1.625,0.281 10 false *1: for TMMT Made 1.458,0.833 2.083,1.177 0.625,0.344 10 false FP+ 1.479,1.5 2.104,1.844 0.625,0.344 10 false FP-

CAUTION / NOTICE / HINT

HINT:
·

If the current from the INJ relay is cut because DTC P062D13 is stored, DTC P123513 will be stored even if the fuel pump assembly (for high pressure side) is normal.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE)
a.

Inspect the fuel pump assembly (for high pressure side).

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL PUMP (for High Pressure)>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump assembly (for high pressure side).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE) - ECM)

NG

REPLACE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE)

2.CHECK HARNESS AND CONNECTOR (FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE) - ECM)
a.

Disconnect the C55 fuel pump assembly (for high pressure side) connector.


b.

Disconnect the C62*1 or C74*2 ECM connector.

*1: for TMMT Made

*2: for TMC Made



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for TMMT Made
Tester Connection Condition Specified Condition
C55-2 (FP+) - C62-28 (FP1+) Always Below 1 Ω
C55-1 (FP-) - C62-29 (FP1-) Always Below 1 Ω
C55-2 (FP+) or C62-28 (FP1+) - Body ground and other terminals Always 10 kΩ or higher
C55-1 (FP-) or C62-29 (FP1-) - Body ground and other terminals Always 10 kΩ or higher

for TMC Made
Tester Connection Condition Specified Condition
C55-2 (FP+) - C74-28 (FP1+) Always Below 1 Ω
C55-1 (FP-) - C74-29 (FP1-) Always Below 1 Ω
C55-2 (FP+) or C74-28 (FP1+) - Body ground and other terminals Always 10 kΩ or higher
C55-1 (FP-) or C74-29 (FP1-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR