B1421/21 Solar Sensor Circuit (Passenger Side)
Diagnostic trouble codes · Vehicles built from Jun 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION


The solar sensor, which is installed on the upper side of the instrument panel, detects sunlight and controls the air conditioning in AUTO mode. The output voltage from the solar sensor varies according to the amount of sunlight. When the sunlight increases, the output voltage increases. As the sunlight decreases, the output voltage decreases. The A/C amplifier detects voltage output from the solar sensor.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1421/21 |
Open or short in passenger side solar sensor circuit |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- If DTC B1244 is output at the same time, troubleshoot DTC B1244 first (Click herefor 2AZ-FE, Click here for 2GR-FE).
- If the check is performed in a dark place, DTC B1421/21 or B1424/24 (solar sensor circuit abnormal) may be output even though the system is normal.
- If DTC B1244 is output at the same time, troubleshoot DTC B1244 first (Click herefor 2AZ-FE, Click here for 2GR-FE).
| 1. READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester main switch on.
Expose the sensing portion of the solar sensor to light.
- HINT:
- Use an incandescent light for inspection.
Select the item below in the Data List, and read the display on the intelligent tester.
| Tester Display |
Measure Item/Range |
Normal Condition |
Diagnostic Note |
| Solar Sensor (P side) (Solar Sens-P) |
Passenger side solar sensor / Min.: 0, Max.: 255 |
Passenger side solar sensor value increases as brightness increases |
- |
- OK:
- The display is as specified in the normal condition column.
- Result:
Result
Proceed to
NG
A
OK (When troubleshooting according to the PROBLEM SYMPTOMS TABLE)
B
OK (When troubleshooting according to the DTC)
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (SOLAR SENSOR) |
Disconnect the solar sensor connector.

Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
E11-6 (CLTB) - E11-3 (CLTE) (*1, *2)
Ignition switch off
Below 1 V
E11-6 (CLTB) - E11-3 (CLTE) (*1, *2)
Ignition switch on (IG)
10 to 14 V
h1-6 (CLTB) - h1-3 (CLTE) (*3)
Ignition switch off
Below 1 V
h1-6 (CLTB) - h1-3 (CLTE) (*3)
Ignition switch on (IG)
10 to 14 V
- HINT:
- *1: LHD with the 2GR-FE
- *2: RHD with the 2AZ-FE
- *3: RHD with the 2GR-FE
- *1: LHD with the 2GR-FE
|
|
||||
| NG | |
| 3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SOLAR SENSOR) |
Disconnect the main body ECU connector.

Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
E6-20 (CLTB) - E11-6 (CLTB) (*1, *2)
Always
Below 1 Ω
E6-18 (CLTE) - E11-3 (CLTE) (*1, *2)
Always
Below 1 Ω
E6-20 (CLTB) - h1-6 (CLTB) (*3)
Always
Below 1 Ω
E6-18 (CLTE) - h1-3 (CLTE) (*3)
Always
Below 1 Ω
E6-20 (CLTB) - Body ground
Always
10 kΩ or higher
E6-18 (CLTE) - Body ground
Always
10 kΩ or higher
- HINT:
- *1: LHD with the 2GR-FE
- *2: RHD with the 2AZ-FE
- *3: RHD with the 2GR-FE
- *1: LHD with the 2GR-FE
|
|
||||
| OK | ||
| ||
| 4. CHECK SOLAR SENSOR |
Remove the solar sensor with its connector still connected.

Connect the positive (+) lead from the battery to terminal 6 (CLTB), and the negative (-) lead to terminal 3 (CLTE) of the solar sensor.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
- LHD:
Tester Connection
Condition
Specified Condition
E11-2 (TSR) - E11-3 (CLTE) (*1)
Sensor is subjected to electric light
0.8 to 4.3 V
E11-2 (TSR) - E11-3 (CLTE) (*1)
Sensor is covered with a cloth
Below 0.8 V
- RHD:
Tester Connection
Condition
Specified Condition
E11-1 (TSL) - E11-3 (CLTE) (*2)
Sensor is subjected to electric light
0.8 to 4.3 V
E11-1 (TSL) - E11-3 (CLTE) (*2)
Sensor is covered with a cloth
Below 0.8 V
h1-1 (TSL) - h1-3 (CLTE) (*3)
Sensor is subjected to electric light
0.8 to 4.3 V
h1-1 (TSL) - h1-3 (CLTE) (*3)
Sensor is covered with a cloth
Below 0.8 V
- HINT:
- *1: LHD with the 2GR-FE
- *2: RHD with the 2AZ-FE
- *3: RHD with the 2GR-FE
- *1: LHD with the 2GR-FE
- NOTICE:
- The connection procedure for using a digital tester such as a TOYOTA electrical tester is shown above. When using an analog tester, connect the negative (-) lead to terminal 6, and the positive (+) lead to terminal 3 of the solar sensor.
- While using the battery during inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.
- The connection procedure for using a digital tester such as a TOYOTA electrical tester is shown above. When using an analog tester, connect the negative (-) lead to terminal 6, and the positive (+) lead to terminal 3 of the solar sensor.
- HINT:
- Use an incandescent light for inspection. Bring it within about 30 cm (11.8 in.) of the solar sensor.
- As the inspection light is moved away from the sensor, the voltage decreases.
- Use an incandescent light for inspection. Bring it within about 30 cm (11.8 in.) of the solar sensor.
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (SOLAR SENSOR - A/C AMPLIFIER) |
Disconnect the solar sensor connector.

Disconnect the A/C amplifier connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- LHD:
Tester Connection
(Symbols)
Condition
Specified Condition
E38-32 (TSP) - E11-2 (TSR) (*1)
Always
Below 1 Ω
E38-32 (TSP) - Body ground (*1)
Always
10 kΩ or higher
- RHD:
Tester Connection
(Symbols)
Condition
Specified Condition
E38-32 (TSP) - E11-1 (TSL) (*2)
Always
Below 1 Ω
E38-32 (TSP) - h1-1 (TSL) (*3)
Always
Below 1 Ω
E38-32 (TSP) - Body ground (*2, *3)
Always
10 kΩ or higher
- HINT:
- *1: LHD with the 2GR-FE
- *2: RHD with the 2AZ-FE
- *3: RHD with the 2GR-FE
- *1: LHD with the 2GR-FE
|
|
||||
| OK | ||
| ||
