2006-2011 Camry Aurion · Service Manual HEATER & AIR CONDITIONING SYSTEM

B1422/22 Compressor Lock Sensor Circuit

Diagnostic trouble codes · Vehicles built from Oct 2006

SYSTEM DESCRIPTION

The ECM sends a signal to the A/C amplifier via CAN communication.
The A/C amplifier reads the difference between compressor speed and engine speed. When the difference becomes too large, the A/C amplifier determines that the compressor locks, and turns the magnetic clutch off.
DTC No.
DTC Detection Condition
Trouble Area
B1422/22
Open or short in compressor lock sensor circuit
  1. A/C compressor (A/C lock sensor)
  2. Compressor drive belt
  3. Harness or connector between compressor and magnetic clutch (A/C lock sensor)
  4. A/C amplifier
  5. CAN communication system

WIRING DIAGRAM

E211335E01

INSPECTION PROCEDURE


1. CHECK CAN COMMUNICATION SYSTEM
  1. Use the intelligent tester to check if the CAN communication system is functioning normally.

    Result:
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM
A


2. INSPECT AIR CONDITIONING AMPLIFIER

  1. E124471E03
    Remove the A/C amplifier with the connectors still connected.

  1. E116941E03
    Measure the waveform of the connector.
    Item
    Contents
    Tool setting
    200 mV/DIV., 10 ms./DIV.
    Vehicle condition
    Engine is running
    A/C switch: ON
    Blower switch: LO

    Standard:
    Tester Connection (Symbols)
    Condition
    Specified Condition
    E38-8 (LOCK) - E38-13 (SG-2)
    Engine is running
    A/C switch: ON
    Blower switch: LO
    Pulse generation

    Result:
    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to the PROBLEM SYMPTOMS TABLE)
    B
    OK (When troubleshooting according to the DTC)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPLACE AIR CONDITIONING AMPLIFIER
A


3. INSPECT COMPRESSOR AND MAGNETIC CLUTCH (A/C LOCK SENSOR)

  1. E005280
    Disconnect the connector from the A/C compressor.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    C53-1 (SSR+) - C53-2 (SSR-)
    20°C (68°F)
    160 to 320 Ω



NG
REPLACE COMPRESSOR AND MAGNETIC CLUTCH (A/C LOCK SENSOR)
OK


4. CHECK HARNESS AND CONNECTOR (A/C AMPLIFIER - A/C LOCK SENSOR)

  1. E124470E05
    Disconnect the connector from the A/C amplifier.

  1. E124442E04
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection (Symbols)
    Condition
    Specified Condition
    E38-8 (LOCK) - C53-1 (SSR+)
    Always
    Below 1 Ω
    E38-13 (SG-2) - C53-2 (SSR-)
    Always
    Below 1 Ω
    E38-8 (LOCK) - Body ground
    Always
    10 kΩ or higher
    E38-13 (SG-2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER


← B1421/21 Solar Sensor Circuit (Passenger Side) (from Jun 2009)B1423/23 Pressure Sensor Circuit (from Jun 2006) →