P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)
Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The park/neutral position switch detects the shift lever position and sends signals to the TCM.| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0705 |
(A) Any 2 or more signals of the following are ON simultaneously (2-trip detection logic)
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- According to the DATA LIST displayed on the intelligent tester, you can read the value of switches, sensors, actuators and other items without removing any parts. Reading the DATA LIST as the first step in troubleshooting is one method to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
| READ DATA LIST |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn on the tester.
Select the following items: "Powertrain / ECT / Data List".
According to the display on the tester, read "DATA LIST".
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Neutral Position SW Signal
PNP SW Status / ON or OFF
Shift lever position is;
P and N: ON
Except P or N: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
Shift SW status (R Range)
PNP SW Status / ON or OFF
Shift lever position is;
R: ON
Except R: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
Shift SW status (D Range)
PNP SW Status / ON or OFF
Shift lever position is;
D and S: ON
Except D or S: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
| 1. CHECK HARNESS AND CONNECTOR (D, R POSITION CIRCUIT) |
Disconnect the park/neutral position switch connector.

Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Specified Condition
RB (C1-1) - Body ground
10 to 14 V
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY) |
Remove the ST relay from the engine room relay block.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Specified Condition
L (C1-9) - ST relay terminal 1
Below 1 Ω
|
|
||||
| OK | |
| 3. INSPECT ST RELAY |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Specified Condition
3 - 5
10 kΩ or higher
3 - 5
Below 1 Ω
Apply battery voltage between terminals 1 and 2
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND) |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Specified Condition
ST relay terminal 2 - Body ground
Below 1 Ω
|
|
||||
| OK | |
| 5. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

- Standard resistance:
Shift Position
Tester Connection
Specified Condition
P
B (C1-4) - L (C1-9)
Below 1 Ω
Except P
10 kΩ or higher
R
RB (C1-1) - RL (C1-2)
Below 1 Ω
Except R
10 kΩ or higher
N
B (C1-4) - L (C1-9)
Below 1 Ω
Except N
10 kΩ or higher
D, S, ''+'' and ''-''
RB (C1-1) - DL (C1-7)
Below 1 Ω
Except D, S, ''+'' and ''-''
10 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (IG1 RELAY - TCM) |
Connect the park/neutral position switch connector.

Disconnect the TCM connector.
Turn the ignition switch on (IG), and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.
- Standard voltage:
Shift Position
Tester Connection
Specified Condition
R
R (C56-15) - Body ground
10 to 14 V *
Except R
Below 1 V
D
D (C56-16) - Body ground
10 to 14 V
Except D
Below 1 V
- HINT:
- *: The voltage will drop slightly due to lighting up of the back up light.
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
Disconnect the TCM connector.

Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
B (C1-4) - NSW (C56-11)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
B (C1-4) or NSW (C56-11) - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||
