2006-2011 Camry Aurion · Service Manual TRANSMISSION

P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)

Diagnostic trouble codes · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the TCM.
DTC No.
DTC Detection Condition
Trouble Area
P0705
(A) Any 2 or more signals of the following are ON simultaneously (2-trip detection logic)
  1. NSW input signal
  2. R input signal
  3. D input signal
(B) All switches are OFF simultaneously for NSW, R and D.
  1. Short in park/neutral position switch circuit
  2. Park/neutral position switch
  3. TCM

WIRING DIAGRAM

C226005E01

INSPECTION PROCEDURE

HINT:
According to the DATA LIST displayed on the intelligent tester, you can read the value of switches, sensors, actuators and other items without removing any parts. Reading the DATA LIST as the first step in troubleshooting is one method to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


READ DATA LIST
  1. Turn the ignition switch off.

  2. Connect the intelligent tester to the DLC3.

  3. Turn the ignition switch on (IG).

  4. Turn on the tester.

  5. Select the following items: "Powertrain / ECT / Data List".

  6. According to the display on the tester, read "DATA LIST".

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP SW Status / ON or OFF
    Shift lever position is;
    P and N: ON
    Except P or N: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    Shift SW status (R Range)
    PNP SW Status / ON or OFF
    Shift lever position is;
    R: ON
    Except R: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    Shift SW status (D Range)
    PNP SW Status / ON or OFF
    Shift lever position is;
    D and S: ON
    Except D or S: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.


1. CHECK HARNESS AND CONNECTOR (D, R POSITION CIRCUIT)

  1. C117645E20
    Disconnect the park/neutral position switch connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    RB (C1-1) - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY)

  1. C145251E01
    Remove the ST relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    L (C1-9) - ST relay terminal 1
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT ST RELAY

  1. B016200E02
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    Apply battery voltage between terminals 1 and 2



NG
REPLACE ST RELAY
OK


4. CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

  1. C145252E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    ST relay terminal 2 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C110340E63
    Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Standard resistance:
    Shift Position
    Tester Connection
    Specified Condition
    P
    B (C1-4) - L (C1-9)
    Below 1 Ω
    Except P
    10 kΩ or higher
    R
    RB (C1-1) - RL (C1-2)
    Below 1 Ω
    Except R
    10 kΩ or higher
    N
    B (C1-4) - L (C1-9)
    Below 1 Ω
    Except N
    10 kΩ or higher
    D, S, ''+'' and ''-''
    RB (C1-1) - DL (C1-7)
    Below 1 Ω
    Except D, S, ''+'' and ''-''
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (IG1 RELAY - TCM)

  1. C133210E05
    Connect the park/neutral position switch connector.

  1. Disconnect the TCM connector.

  1. Turn the ignition switch on (IG), and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

    Standard voltage:
    Shift Position
    Tester Connection
    Specified Condition
    R
    R (C56-15) - Body ground
    10 to 14 V *
    Except R
    Below 1 V
    D
    D (C56-16) - Body ground
    10 to 14 V
    Except D
    Below 1 V

    HINT:
    *: The voltage will drop slightly due to lighting up of the back up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

  1. C122809E13
    Disconnect the TCM connector.

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    B (C1-4) - NSW (C56-11)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    B (C1-4) or NSW (C56-11) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM (Click here)


← P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) (Oct 2006 – May 2009)P0710 Transmission Fluid Temperature Sensor "A" Circuit (+ P0712, P0713) (from Oct 2006) →