2006-2011 Camry Aurion · Service Manual ENGINE

P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)

Diagnostic trouble codes · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the ECM.
DTC No.
DTC Detection Condition
Trouble Area
P0705
(A) Any 2 or more signals of the following are ON simultaneously (2-trip detection logic):
  1. P input signal
  2. N input signal
  3. R input signal
  4. D input signal
(B) Any 2 or more signals of the following are ON simultaneously (2-trip detection logic):
  1. NSW input signal
  2. R input signal
  3. D input signal
(C) Any of following conditions is met for 2.0 sec. or more with the shift lever in the S position (2-trip detection logic).
  1. NSW input signal is ON.
  2. P input signal is ON.
  3. N input signal is ON.
  4. R input signal is ON.
(D) All switches are OFF simultaneously for NSW, P, R, N and D.
  1. Short in park/neutral position switch circuit
  2. Park/neutral position switch
  3. ECM

WIRING DIAGRAM

A153242E02

INSPECTION PROCEDURE

HINT:
According to the DATA LIST displayed on the intelligent tester, you can read the values of the switches, sensors, actuators and so on without parts removal. Reading the DATA LIST as the first step in troubleshooting is one method to shorten labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


READ DATA LIST
  1. Turn the ignition switch off.

  2. Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.

  3. Turn the ignition switch on (IG).

  4. Turn on the tester.

  5. Select the item "Powertrain / Engine / Data List".

  6. According to the display on the tester, read the "DATA LIST".

    Item
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP SW Status / ON or OFF
    Shift lever position is;
    P and N: ON
    Except P or N: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    Shift SW status (R Range)
    PNP SW Status / ON or OFF
    Shift lever position is;
    R: ON
    Except R: OFF
    ↑
    Shift SW status (D Range)
    PNP SW Status / ON or OFF
    Shift lever position is;
    D and S: ON
    Except D or S: OFF
    ↑


1. CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)

  1. C117645E42
    Disconnect the park/neutral position switch connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    RB (C1-1) - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY)

  1. A137047E12
    Disconnect the C1 park/neutral position switch connector.

  1. Remove the ST relay from the engine room relay block.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Tester Connection
    Specified Condition
    L (C1-9) - ST relay terminal 1
    Below 1 Ω

  1. Reconnect the park/neutral position switch connector.

  1. Install the ST relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT ST RELAY

  1. B016200E02
    Remove the ST relay from the engine room relay block.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    Apply battery voltage between terminals 1 and 2

  1. Install the ST relay.



NG
REPLACE ST RELAY
OK


4. CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

  1. A137046E01
    Remove the ST relay from the engine room relay block.

  1. Measure the resistance between the terminals

    Standard resistance:
    Tester Connection
    Specified Condition
    ST relay terminal 2 - Body ground
    Below 1 Ω

  1. Install the ST relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C110340E67
    Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Standard resistance:
    Shift Position
    Tester Connection
    Specified Condition
    P
    RB (C1-1) - PL (C1-3) and B (C1-4) - L (C1-9)
    Below 1 Ω
    Except P
    10 kΩ or higher
    R
    RB (C1-1) - RL (C1-2)
    Below 1 Ω
    Except R
    10 kΩ or higher
    N
    RB (C1-1) - NL (C1-8) and B (C1-4) - L (C1-9)
    Below 1 Ω
    Except N
    10 kΩ or higher
    D, S, ''+'' and ''-''
    RB (C1-1) - DL (C1-7)
    Below 1 Ω
    Except D, S, ''+'' and ''-''
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

  1. C136857E07
    Connect the park/neutral position switch connector.

  1. Disconnect the ECM connectors.

  1. Turn the ignition switch on (IG), and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

    Standard voltage:
    Shift Position
    Tester Connection
    Specified Condition
    P
    P (C58-24)*1 - Body ground
    P (C55-24)*2 - Body ground
    10 to 14 V
    Except P
    Below 1 V
    N
    N (C58-27)*1 - Body ground
    N (C55-27)*2 - Body ground
    10 to 14 V
    Except N
    Below 1 V
    R
    R (C58-25)*1 - Body ground
    R (C55-25)*2 - Body ground
    10 to 14 V*3
    Except R
    Below 1 V
    D and S
    D (C58-26)*1 - Body ground
    D (C55-26)*2 - Body ground
    10 to 14 V
    Except D and S
    Below 1 V
    S, ''+'' and ''-''
    S (A24-25)*1 - Body ground
    S (A55-25)*2 - Body ground
    10 to 14 V
    Except S, ''+'' and ''-''
    Below 1 V

    HINT:
    *1: RHD
    *2: LHD
    *3: The voltage will drop slightly due to lighting up of the back up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK TRANSMISSION CONTROL SWITCH (IG VOLTAGE)

  1. C110345E31
    Disconnect the transmission control switch connector of the shift lock control unit assembly.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminals.

    Standard voltage:
    Tester Connection
    Specified Condition
    IG (E31-3) - Body ground
    10 to 14 V

  1. Reconnect the transmission control switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. INSPECT TRANSMISSION CONTROL SWITCH

  1. C136860E10
    Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Standard resistance:
    Shift Position
    Tester Connection
    Specified Condition
    S, ''+'' and ''-''
    IG (E31-3) - S (E31-7)
    Below 1 Ω
    Except S, ''+'' and ''-''
    10 kΩ or higher



NG
REPLACE TRANSMISSION CONTROL SWITCH
OK


9. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

  1. C136861E13
    Disconnect the ECM connectors.

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    RHD:
    Tester Connection
    Specified Condition
    B (C1-4) - NSW (C58-62)
    Below 1 Ω
    LHD:
    Tester Connection
    Specified Condition
    B (C1-4) - NSW (C55-62)
    Below 1 Ω


    Standard resistance (Check for short):
    RHD:
    Tester Connection
    Specified Condition
    B (C1-4) or NSW (C58-62) - Body ground
    10 kΩ or higher
    LHD:
    Tester Connection
    Specified Condition
    B (C1-4) or NSW (C55-62) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) (Oct 2006 – May 2009)P1660 VSV for AICVS Circuit (Oct 2006 – May 2009) →