P1660 VSV for AICVS Circuit
Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The air cleaner is equipped with two inlets, one of which is opened or closed by the Air Intake Control Valve (AICV). This system reduces intake noise and increases engine power at low to high engine speed range.When the engine is operating in the low-to-mid speed range, this control operates the AICV to close one of the air cleaner inlets. When the engine speed is more than 3,600 rpm and the opening angle of the throttle valve is more than 60°, the ECM activates the VSV and opens the AICV.


| DTC No. |
Detection Condition |
Trouble Area |
| P1660 |
The following conditions are met simultaneously for 0.5 seconds or more (2 trip detection logic):
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (VSV FOR AICV) |
Turn the ignition switch on (IG) and turn the intelligent tester ON.

Select the following menu items: Powertrain / Engine / Active Test / Active the VSV for ACIS and operate the VSV for AICV.
Check the operation of the VSV when the VSV is operated by the intelligent tester.
- Standard:
Tester Operation
Specified Condition
VSV is ON
Air from port E flows out through port F
VSV is OFF
Air from port E flows out through the air filter
|
|
||||
| NG | |
| 2. CHECK VSV ASSEMBLY (FOR AICV) |
Inspect the intake air control valve assembly (Click here).
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (VSV FOR AICV - EFI MAIN RELAY) |
Check the wire harness between the VSV for AICV connector and the ECM connector.

Disconnect the A53 VSV for AICV connector.
Disconnect the A24 (RHD) or A55 (LHD) ECM connector.
Measure the resistance between the terminals of the wire harness side connectors and body ground.
- Standard resistance (Check for open):
- RHD:
Tester Connection
Specified Condition
VSV for AICV (A53-2) - AICV (A24-4)
Below 1 Ω
- LHD:
Tester Connection
Specified Condition
VSV for AICV (A53-2) - AICV (A55-4)
Below 1 Ω
- Standard resistance (Check for short):
- RHD:
Tester Connection
Specified Condition
VSV for AICV (A53-2) or AICV (A24-4) - Body ground
10 kΩ or higher
- LHD:
Tester Connection
Specified Condition
VSV for AICV (A53-2) or AICV (A55-4) - Body ground
10 kΩ or higher
Check the EFI No. 3 fuse.
Remove the EFI No. 3 fuse from the engine room R/ B.
Measure the resistance of the EFI No. 3 fuse.
- Standard resistance:
- Below 1 Ω
Reinstall the EFI No. 3 fuse.
Check the wire harness between the VSV for AICV and the EFI relay.
Remove the engine room junction block from the engine room R/B.
Measure the resistance between the terminals of the wire harness side connectors.
- Standard resistance:
- Check for open:
Tester Connection
Specified Condition
VSV for AICV (A53-1) - 1E-6
Below 1 Ω
Reconnect the VSV for AICV connector.
Reinstall the engine room junction block.
|
|
||||
| OK | |
| 4. INSPECT VACUUM TANK |
Inspect the vacuum tank (Click here).
|
|
||||
| OK | ||
| ||
