DIAGNOSIS SYSTEM
Troubleshooting · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| BUS CHECK (COMMUNICATION MALFUNCTION DTC) |
- HINT:
- Only CAN communication system DTCs for each ECU can be displayed on the intelligent tester.
Select "Bus Check" from the "System Select" screen on the intelligent tester.

Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter".

Select the system of the DTC to be checked and select "Details".

CAN communication system DTC(s) is/are displayed.

| CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT USE CAN COMMUNICATION |
Systems (ECUs, sensors) that use CAN communication vary depending on the vehicle's optional equipments. Check which systems (ECUs, sensors) are installed on the vehicle.
ECU/Sensor name
Check method
ABS / VSC / TRC
Installed on all vehicles
Engine
Installed on all vehicles
ECT
Installed on vehicles with automatic transaxle
SRS Airbag
Installed on all vehicles
Air Conditioner
Installed on all vehicles
Combination Meter
Installed on all vehicles
Main Body
Installed on all vehicles
| DTC TABLE BY ECU |
- HINT:
- For the CAN communication system, CAN communication system DTCs stored in certain ECUs can be displayed using the intelligent tester.
- If CAN communication system DTCs are output, trouble cannot be determined only by the DTCs. Perform troubleshooting according to "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here).
- For the CAN communication system, CAN communication system DTCs stored in certain ECUs can be displayed using the intelligent tester.
ECM (2AZ-FE)
DTC No.
Detection Item
U0101*
High Speed CAN Communication Bus
- HINT:
- DTC communication is via the CAN communication system.
- *: The ECM is malfunctioning if only U0101 is output. Replace the ECM.
- DTC communication is via the CAN communication system.
ECM (2GR-FE)
DTC No.
Detection Item
U0101*
High speed CAN Communication Bus
- HINT:
- DTC communication is via the CAN communication system.
- *: The ECM is malfunctioning if only U0101 is output. Refer to SFI system (Click here).
- DTC communication is via the CAN communication system.
ECT (2AZ-FE)
DTC No.
Detection Item
U0100*
High Speed CAN Communication Bus
- HINT:
- DTC communication is via the CAN communication system.
- *: The ECM is malfunctioning if only U0100 is output. Replace the ECM.
- DTC communication is via the CAN communication system.
ECT (2GR-FE)
DTC No.
Detection Item
U0100*
High speed CAN Communication Bus
- HINT:
- DTC communication is via the CAN communication system.
- *: The ECM is malfunctioning if only U0100 is output. Refer to Automatic Transaxle system (Click here).
- DTC communication is via the CAN communication system.
SKID CONTROL ECU
DTC No.
Detection Item
U0073
Control Module Communication Bus Off
- HINT:
- DTC communication is via the CAN communication system.
COMBINATION METER ECU
DTC No.
Detection Item
U0100
Lost Communication with ECM/PCM "A"
U0129
Lost Communication with Brake System Control Module
- HINT:
- DTC communication is via the CAN communication system.
AIR CONDITIONER AMPLIFIER
DTC No.
Detection Item
B1499
Multiplex Communication Circuit
- HINT:
- DTC communication is via the CAN communication system.
MAIN BODY ECU
- HINT:
- Although the main body ECU is connected to the CAN communication system, CAN communication DTCs are not output.
CENTER AIRBAG SENSOR
- HINT:
- Although the center airbag sensor is connected to the CAN communication system, CAN communication DTCs are not output.
| DTC COMBINATION TABLE |
| DTC |
Trouble Mode |
||||||
| Output from |
Output DTC |
ECM Communication Stop Mode |
Skid Control ECU Communication Stop Mode |
Combination Meter ECU Communication Stop Mode |
Air Conditioning Amplifier Communication Stop Mode |
Center Airbag Sensor Communication Stop Mode |
Main Body ECU Communication Stop Mode |
| Skid Control ECU |
U0073 |
X |
X |
X |
X |
X |
X |
| Combination Meter ECU |
U0100 |
○ |
X |
X |
X |
X |
X |
| U0129 |
X |
○ |
X |
X |
X |
X |
|
| No DTC |
X |
X |
○ |
○ |
○ |
○ |
|
- HINT:
- ○: Set
- X: Not set or may be set depending on the malfunctioning part when one side of the CAN bus wire becomes open
- ○: Set
Perform troubleshooting according to the combination of DTCs output.
- HINT:
- ECM Communication Stop Mode (Click here)
- Skid Control ECU Communication Stop Mode (Click here)
- Combination Meter ECU Communication Stop Mode (Click here)
- Center Airbag Sensor Communication Stop Mode (Click here)
- Air Conditioning Amplifier Communication Stop Mode (Click here)
- Main Body ECU Communication Stop Mode (Click here)
- ECM Communication Stop Mode (Click here)