Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM
Cranking Holding Function Circuit
Circuit diagnosis · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The cranking holding control system provides current to the starter when the ECM detects the engine switch's start signal (STSW). When the ECM performs a firing judgment, the system cuts current to the starter. When an ECM receives the STSW signal, it turns on the ST CUT relay, which prevents flickering of the combination meter, clock, audio system, etc. Also, the ECM sends a signal to the ECM's STAR terminal. Then the STAR output signal travels through the Park/Neutral Position (PNP) switch to the STARTER relay, causing the starter to be activated. When the engine is cranking, the starter operation signal is sent to the ECM's STA terminal. WIRING DIAGRAM
Refer to DTC P0617 (Click here ). INSPECTION PROCEDURE
1. CHECK CRANKING
When starting the engine, check whether the starter motor starts.
OK
CHECK FOR INTERMITTENT PROBLEMS
NG
2. READ VALUE USING INTELLIGENT TESTER (STA SIGNAL)
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Select the following menu items: Powertrain / Engine / Data List / Starter Signal. Read the values.
Check the result when the engine switch is turned on (IG) and when the engine is started.
Standard:
Display (Starter Signal)
Condition
OFF
Engine switch on (IG)
ON
Engine starts
OK
NG
3. INSPECT ECM (STSW VOLTAGE)
Disconnect the A24 (RHD) or A55 (LHD) ECM connector.
Measure the voltage between the terminal of the ECM connector and body ground while cranking the engine.
Standard voltage:
RHD:
Tester Connection
Specified Condition
STSW (A24-14) - Body ground
9 to 14 V
LHD:
Tester Connection
Specified Condition
STSW (A55-14) - Body ground
9 to 14 V
Reconnect the ECM connector.
NG
OK
4. INSPECT ECM (STAR VOLTAGE)
Remove the ST CUT relay from the engine room R/B.
Measure the voltage between the terminals of the engine room R/B and body ground while cranking the engine.
Standard voltage:
Tester Connection
Specified Condition
ST CUT relay (3) - Body ground
9 to 14 V
Reinstall the ST CUT relay.
NG
OK
5. INSPECT ST CUT RELAY
Remove the ST CUT relay from the engine room R/B.
Measure the resistance between the terminals.
Standard resistance:
Tester Connection
Specified Condition
3 - 5
10 kΩ or higher
3 - 5
Below 1 Ω (when battery voltage applied to terminals 1 and 2)
Reinstall the ST CUT relay.
NG
OK
6. INSPECT PARK/NEUTRAL SWITCH ASSEMBLY
Inspect the Park/Neutral Position (PNP) switch.
Disconnect the C1 switch connector.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Gear Selector Lever Position
Tester Connection
Specified Condition
P
B (C1-4) - L (C1-9)
Below 1 Ω
N
B (C1-4) - L (C1-9)
Below 1 Ω
Reconnect the PNP switch connector.
NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here )
OK
CHECK HARNESS AND CONNECTOR
7. INSPECT STARTER RELAY
Remove the ST relay from the engine room R/B.
Measure the resistance between the terminals.
Standard resistance:
Tester Connection
Specified Condition
3 - 5
10 kΩ or higher
3 - 5
Below 1 Ω (when battery voltage applied to terminals 1 and 2)
Reinstall the ST relay.
NG
OK
8. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - STARTER RELAY)
Disconnect the C1 park/neutral position switch connector.
Remove the ST relay from the engine room R/B.
Measure the resistance according to the value(s) in the table below.
Standard resistance (Check for open):
Tester Connection
Specified Condition
L (C1-9) - ST relay terminal (1)
Below 1 Ω
Standard resistance (Check for open):
Tester Connection
Specified Condition
L (C1-9) or ST relay terminal (1) - Body ground
10 kΩ or higher
Reinstall the ST relay.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
9. INSPECT ENGINE ROOM RELAY BLOCK (STARTER RELAY VOLTAGE)
Remove the ST relay from the engine room R/B.
Measure the voltage between the terminals of the engine room R/B and body ground.
Standard voltage:
Tester Connection
Specified Condition
ST relay (5) - Body ground
9 to 14 V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
10. INSPECT STARTER ASSEMBLY
Inspect the starter assembly (Click here ).
NG
REPAIR OR REPLACE STARTER ASSEMBLY
OK
REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER RELAY - STARTER, STARTER - BATTERY)
11. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM)
Disconnect the E9 main body ECU connector.
Disconnect the A24 (RHD) or A55 (LHD) ECM connector.
Measure the resistance according to the value(s) in the table below.
Standard resistance (Check for open):
RHD:
Tester Connection
Specified Condition
STSW (E9-4) - STSW (A24-14)
Below 1 Ω
LHD:
Tester Connection
Specified Condition
STSW (E9-4) - STSW (A55-14)
Below 1 Ω
Standard resistance (Check for short):
RHD:
Tester Connection
Specified Condition
STSW (E9-4) or STSW (A24-14) - Body ground
10 kΩ or higher
LHD:
Tester Connection
Specified Condition
STSW (E9-4) or STSW (A55-14) - Body ground
10 kΩ or higher
Reconnect the main body ECU connector.
Reconnect the ECM connector.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK