2006-2011 Camry Aurion · Service Manual ENGINE

P0300 Random / Multiple Cylinder Misfire Detected

Diagnostic trouble codes · Vehicles built Jun 2006 – Sep 2006

Also covers:

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

A093767E03
When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high HC concentration levels can cause increases in exhaust emission levels. High concentrations of HC can also cause increases in the Three-Way Catalytic Converter (TWC) temperature, which may cause damage to the TWC. To prevent these increases in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the TWC reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the Camshaft Position (CMP) sensor and the Crankshaft Position (CKP) sensor. The CMP sensor is used to identify any misfiring cylinders and the CKP sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds.
If the misfire rate exceeds the threshold level, and could cause emission deterioration, the ECM illuminates the MIL and sets a DTC.
DTC No.
DTC Detection Condition
Trouble Area
P0300
Simultaneous misfiring of several cylinders is detected
(2-trip detection logic)
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connections
  4. Ignition system
  5. Injector
  6. Fuel pressure
  7. Mass Air Flow (MAF) meter
  8. Engine Coolant Temperature (ECT) sensor
  9. Compression pressure
  10. Valve clearance
  11. Valve timing
  12. Ventilation valve and hose
  13. Ventilation hose connection
  14. Air induction system
  15. ECM
P0301
P0302
P0303
P0304
Misfiring of specific cylinder is detected
(2-trip detection logic)
When DTCs for misfiring cylinders are randomly set, but DTC P0300 is not set, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only set when several misfiring cylinders are detected at the same time.

WIRING DIAGRAM


  1. Wiring diagram of the ignition system

    A142852E01

    A142853E02

  1. Wiring diagram of the injector circuit

    A142854E02

CONFIRMATION DRIVING PATTERN

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to the ON position and turn the tester on.
  3. Record the DTC(s) and freeze frame data.
  4. Using the tester, switch the ECM from normal mode to check mode (Click here).
  5. Read the misfire counts of each cylinder (Cylinder #1, #2, #3 and #4) with the engine in an idling condition. If any misfire count is displayed, skip the following confirmation driving pattern.
  6. Drive the vehicle several times with the conditions, such as engine rpm and engine load, shown in Misfire RPM and Misfire Load in the Data List.

    HINT:
    In order to store misfire DTCs, it is necessary to drive the vehicle for the period of time shown in the table below, with the Misfire RPM and Misfire Load in the Data List.
    Engine RPM
    Duration
    Idling
    8 minutes or more
    1,000
    4 minutes 30 seconds or more
    2,000
    2 minutes 30 seconds or more
    3,000
    1 minutes 30 seconds or more

  7. Check whether misfires have occurred by checking for DTCs and freeze frame data.

    HINT:
    Do not turn the ignition switch off until the stored DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data will be erased.

  8. Record the DTC(s), freeze frame data and misfire counts.
  9. Turn the ignition switch off and wait for at least 5 seconds.

INSPECTION PROCEDURE

HINT:
  1. If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the freeze frame data.
  4. If the misfire still cannot be reproduced even though the conditions stored in the freeze frame data have been duplicated, one of the following factors is considered to be a possible cause of the problem:
    1. The fuel level is low.
    2. Improper fuel is used.
    3. The spark plugs are dirty.
    4. The problem is complex and involves multiple factors.
  5. After finishing repairs, check that no misfire occurs in each cylinder (Cylinder #1, #2, #3 and #4).
  6. Be sure to confirm that no misfiring cylinder DTCs are set again by conducting the confirmation driving pattern, after the repairs.
  7. When either Short FT #1 or Long FT #1 in the freeze frame data is outside the range of +-20%, the air-fuel ratio may be rich (-20% or less) or lean (+20% or more).
  8. When the Coolant Temp in the freeze frame data is less than 75°C (167°F), misfires occurred only while warming up the engine.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0300, P0301, P0302, P0303 and/or P0304
    A
    P0300, P0301, P0302, P0303 and/or P0304 and other DTCs
    B

HINT:
If any DTCs other than P0300, P0301, P0302, P0303 and P0304 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2. READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Misfire RPM and Misfire Load.

  1. Read and note the Misfire RPM and Misfire Load (engine load) values.

    HINT:
    The Misfire RPM and Misfire Load indicate the vehicle conditions under which the misfire occurred.


NEXT


3. CHECK VENTILATION HOSE CONNECTIONS

OK:
Ventilation hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE VENTILATION HOSE
OK


4. CHECK MISFIRE COUNT (CYLINDER #1, #2, #3 AND #4)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Cylinder #1 to #4 Misfire Rate.

  1. Allow the engine to idle.

  1. Read each value for Cylinder #1 to #4 Misfire Rate displayed on the tester. If no misfire counts occur in any cylinders, perform the following procedures:

    1. Shift the gear selector lever to the D position.

    2. Check the Cylinder #1 to #4 Misfire Rate.

    3. If misfire counts are still not displayed, perform steps (g) and (h) and then check the misfire counts again.

  1. Drive the vehicle with the Misfire RPM and Misfire Load noted in the "READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD)" procedures above.

  1. Read the Cylinder #1 to #4 Misfire Rate or DTCs displayed on the tester.

    Result:
    Misfire Count
    Proceed to
    Most misfire occurs in only 1 or 2 cylinders
    A
    3 cylinders or more have equal misfire counts
    B

    HINT:
    1. If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
    2. If ECT in the freeze frame data is below 75°C (167°F), the misfire may be detected only when the engine is cold.
    3. If Engine Run Time in the freeze frame data is below 120 seconds, the misfire may be detected immediately after the engine is started.



B
Go to step 14
A


5. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL CUT #1 TO #4)
  1. Allow the engine to idle.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.

  1. If a cylinder has a high misfire count, cut fuel to the cylinder. Compare the misfire count of the cylinder before fuel cut and after fuel cut.

    Result:
    Misfire Count in Each Cylinder
    Proceed to
    Misfire counts of cylinder before fuel cut and after fuel cut are roughly the same
    A
    Misfire count of cylinder before fuel cut is lower than after fuel cut
    B

    NOTICE:
    This Active Test cannot be performed while the vehicle is being driven.

    HINT:
    If the misfire counts of the cylinder before and after the fuel cut are roughly the same, the cylinder is misfiring.
    If the misfire count of the cylinder before the fuel cut is lower than after the fuel cut, the cylinder misfires sometimes.



B
Go to step 11
A


6. CHECK SPARK PLUG

  1. A088861E08
    Remove the ignition coil and the spark plug of the misfiring cylinder.

  1. Measure the spark plug electrode gap.

    Standard gap:
    1.0 to 1.1 mm (0.039 to 0.043 in.)

  1. Check the electrode for carbon deposits.

    Recommended spark plug:
    Manufacturers
    Product
    DENSO
    SK20R11
    NGK
    IFR6A11

    NOTICE:
    If the electrode gap is larger than the standard, replace the spark plug. Do not adjust the electrode gap.

  1. Reinstall the ignition coil and the spark plug.



NG
REPLACE SPARK PLUG
OK


7. CHECK FOR SPARK

  1. A124396
    Perform a spark test.

    CAUTION:
    Always disconnect all fuel injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Remove the ignition coil from the cylinder head.

    2. Install the spark plug onto the ignition coil.

    3. Disconnect the 4 fuel injector connectors.

    4. Attach the spark plug assembly to the cylinder head.

    5. Crank the engine for less than 2 seconds and check for spark.

      OK:
      Sparks jump across electrode gap.

    6. Reconnect the 4 fuel injector connectors.

    7. Install the ignition coil.



NG
Go to step 9
OK


8. CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER
  1. Measure the cylinder compression pressure of the misfiring cylinder (Click here).



OK
Go to step 10
NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

9. CHECK WITH NORMAL SPARK PLUG AND CHECK FOR SPARK OF MISFIRING CYLINDER
  1. Change the installed spark plug with a spark plug that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect all fuel injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug onto the ignition coil.

    2. Disconnect the 4 fuel injector connectors.

    3. Attach the spark plug assembly to the cylinder head.

    4. Crank the engine for less than 2 seconds and check for spark.

      OK:
      Sparks jump across electrode gap.

    5. Reconnect the 4 fuel injector connectors.

    6. Install the ignition coil.



NG
REPLACE IGNITION COIL ASSEMBLY THEN CONFIRM THAT THERE IS NO MISFIRE
OK

REPLACE SPARK PLUG

10. INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30 AND/OR #40 VOLTAGE)

  1. A107892E64
    Disconnect the C24 ECM connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    #10 (C24-108) - E01 (C24-45)
    9 to 14 V
    #20 (C24-107) - E01 (C24-45)
    #30 (C24-106) - E01 (C24-45)
    #40 (C24-105) - E01 (C24-45)

  1. Reconnect the ECM connector.



OK
Go to step 12
NG


11. CHECK HARNESS AND CONNECTOR (INJECTOR - ECM)

  1. A106388E06
    Disconnect the C7 to C10 injector connectors (of the misfiring cylinder).

  1. Disconnect the C24 ECM connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard voltage:
    Cylinder
    Tester Connection
    Specified Condition
    No. 1
    C7-1 - Body ground
    11 to 14 V
    No. 2
    C9-1 - Body ground
    No. 3
    C8-1 - Body ground
    No. 4
    C10-1 - Body ground

    Standard resistance:
    Cylinder
    Tester Connection
    Specified Condition
    No. 1
    C7-2 or #10 (C24-108) - Body ground
    10 kΩ or higher
    C7-2 - #10 (C24-108)
    Below 1 Ω
    No. 2
    C9-2 or #20 (C24-107) - Body ground
    10 kΩ or higher
    C9-2 - #20 (C24-107)
    Below 1 Ω
    No. 3
    C8-2 or #30 (C24-106) - Body ground
    10 kΩ or higher
    C8-2 - #30 (C24-106)
    Below 1 Ω
    No. 4
    C10-2 or #40 (C24-105) - Body ground
    10 kΩ or higher
    C10-2 - #40 (C24-105)
    Below 1 Ω

  1. Reconnect the injector connectors.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12. CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor).



NG
REPLACE FUEL INJECTOR ASSEMBLY
OK


13. CHECK VALVE CLEARANCE OF MISFIRING CYLINDER


NG
ADJUST VALVE CLEARANCE
OK


14. CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leakage.

    OK:
    No leakage from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


15. CHECK VALVE TIMING

  1. A098345E12
    Remove the cylinder head cover.

  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" on the timing chain cover.

  1. Check that the timing marks on the camshaft timing sprocket and camshaft timing gear are facing upward as shown in the illustration.

    1. If not, turn the crankshaft 1 revolution (360°), then align the marks as above.

    OK:
    The timing marks on the camshaft timing gears are aligned as shown in the illustration.

  1. Reinstall the cylinder head cover.



NG
ADJUST VALVE TIMING
OK


16. CHECK FUEL PRESSURE
  1. Check the fuel pressure (Click here).



NG
CHECK AND REPLACE FUEL PUMP, PRESSURE REGULATOR, FUEL PIPE LINE AND FILTER
OK


17. READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature
    With warm engine: Between 75°C and 100°C (167°F and 212°F)



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
OK


18. READ VALUE USING INTELLIGENT TESTER (MASS AIR FLOW RATE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Primary / MAF and Coolant Temp.

  1. Allow the engine to idle until the Coolant Temp reaches 75°C (167°F) or more.

  1. Read the MAF with the engine in an idling condition and at an engine speed of 2,500 rpm.

    Standard:
    MAF while engine idling: Between 0.54 g/sec. and 4.33 g/sec. (Manual transaxle), Between 0.58 g/sec. and 4.67 g/sec. (Automatic transaxle), (shift position: N, A/C: OFF)
    MAF at an engine speed of 2,500 rpm: Between 3.33 g/sec. and 9.17 g/sec. (shift position: N, A/C: OFF)



NG
REPLACE MASS AIR FLOW METER
OK

CHECK FOR INTERMITTENT PROBLEMS


← P0171 System Too Lean (Bank 1) (+ P0172) (from Jun 2009)P0300 Random / Multiple Cylinder Misfire Detected (+ P0301, P0302, P0303, P0304) (Oct 2006 – May 2009) →