2006-2011 Camry Aurion · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


INSPECT ENGINE COOLANT
  1. Inspect the engine coolant (Click here).


INSPECT ENGINE OIL
  1. Inspect the engine oil (Click here).


INSPECT BATTERY
  1. Inspect the battery (Click here).


INSPECT SPARK PLUGS
  1. Inspect the spark plugs (Click here).


INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Remove the air cleaner filter element sub-assembly.

  1. Visually check that there is no dirt, blockage, and/or damage to the air cleaner filter element.

    HINT:
    1. If there is any dirt or a blockage in the air cleaner filter element, clean it with compressed air.
    2. If any dirt or a blockage remains even after cleaning the air cleaner filter element with compressed air, replace it.


INSPECT IGNITION TIMING
  1. Warm up the engine.

  1. C139987E06
    When using the intelligent tester:
    Check the ignition timing.

    1. Connect the intelligent tester to the DLC3.

    2. Enter DATA LIST MODE on the intelligent tester.

      Ignition timing:
      8 to 12° BTDC at idle

      HINT:
      Refer to the intelligent tester operator's manual for help when selecting the DATA LIST.

  1. A082779E69
    When not using the intelligent tester:
    Check the ignition timing.

    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connection with a wrong terminal can damage the electrical system.
      2. Turn off all electrical systems before connecting the terminals.
      3. Perform this inspection after the cooling fan motor has turned off.

    2. A052004
      Remove the No. 1 engine cover.

    3. Pull out the wire harness as shown in the illustration. Connect the clip of the timing light to the wire harness.

      NOTICE:
      1. Use a timing light which can detect the first signal.
      2. After checking, be sure to tape the wire harness.

    4. Check the ignition timing at idle.

      Ignition timing:
      8 to 12° BTDC at idle

      NOTICE:
      When checking the ignition timing, the transmission should be in neutral.

      HINT:
      After the engine rpm is kept at 1,000 to 1,300 rpm for 5 seconds, check that it returns to idle speed.

    5. Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

    6. Check the ignition timing at idle.

      Ignition timing:
      5 to 15° BTDC at idle

    7. Confirm that the ignition timing moves to the advanced angle side when the engine rpm is increased.

    8. Remove the timing light.

    9. Install the No. 1 engine cover.


INSPECT ENGINE IDLE SPEED

  1. C139987E06
    Warm up the engine.

  1. When using the intelligent tester:
    Check the idle speed.

    1. Connect the intelligent tester to the DLC3.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    2. Enter DATA LIST MODE on the intelligent tester.

      Idle speed:
      Item
      Specified Condition
      Manual transmission
      850 to 950 rpm
      Automatic transmission
      610 to 710 rpm

      NOTICE:
      1. When checking the idle speed, the transmission should be in neutral.
      2. Check the idle speed with the cooling fan off.
      3. Switch off all accessories and air conditioning before connecting the intelligent tester.

  1. A082779E70
    When not using the intelligent tester:
    Check the idle speed.

    1. Using SST, connect the tachometer tester probe to terminal 9 (TAC) of the DLC3.

      SST
      09843-18030  

    2. Check the idle speed.

      Idle speed:
      Item
      Specified Condition
      Manual transmission
      850 to 950 rpm
      Automatic transmission
      610 to 710 rpm


INSPECT COMPRESSION
  1. Warm up and stop the engine.

  1. Disconnect the injector connectors.

  1. Remove the ignition coils.

  1. Remove the spark plugs.

  1. A001037
    Check the cylinder compression pressure.

    1. Insert a compression gauge into the spark plug hole.

    2. Fully open the throttle.

    3. While cranking the engine, measure the compression pressure.

      Compression pressure:
      1360 KPa (13.9 kgf/cm2, 198 psi)

      Minimum pressure:
      980 KPa (10 kgf/cm2, 142 psi)

      Difference between each cylinder:
      100 kPa (1.0 kgf/cm2, 14 psi)

      NOTICE:
      1. Always use a fully charged battery to obtain an engine speed of 250 rpm or more.
      2. Check the other cylinders' compression pressure in the same way.
      3. This measurement must be done as quickly as possible.

    4. If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect again.

      HINT:
      1. If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
      2. If pressure stays low, a valve may be stuck or seated improperly, or there may be leakage in the gasket.


INSPECT CO/HC
  1. Start the engine.

  1. Run the engine at 2,500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe during idling.

  1. Immediately check CO/HC concentration at idle and/at 2,500 rpm.

    HINT:
    1. Complete the measurement within 3 minutes.
    2. Check regulations and restrictions in your area when performing 2 mode CO/HC concentration testing (engine check at both idle speed and at 2,500 rpm).

  1. If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.

    1. Check A/F sensor operation (Click here).

    2. Check heated oxygen sensor operation (Click here).

    3. See the table below for possible causes, and then inspect and repair.

      CO
      HC
      Problems
      Causes
      Normal
      High
      Rough idle
      1. Faulty ignition:
        1. Incorrect timing
        2. Fouled, shorted, or improperly gapped plugs
      2. Incorrect valve clearance
      3. Leaking intake or exhaust valves
      4. Compression leaks from cylinders
      Low
      High
      Rough idle
      (fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (black smoke from exhaust)
      1. Restricted air filter
      2. Plugged PCV valve
      3. Faulty SFI system:
        1. Faulty pressure regulator
        2. Defective engine coolant temperature sensor
        3. Defective MAF meter
        4. Faulty ECM
        5. Faulty injectors
        6. Faulty throttle position sensor

← INSPECTION (from Oct 2006)INSPECTION (Oct 2006 – May 2009) →