2006-2011 Camry Aurion · Service Manual ENGINE

B2278 Engine Switch Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Jun 2009

DESCRIPTION

This DTC is output when 1) a malfunction is detected between the main body ECU (instrument panel junction block assembly) and the engine switch; or 2) either of the switches inside the engine switch is malfunctioning.
DTC No.
DTC Detection Condition
Trouble Area
B2278
Communication is abnormal between the main body ECU (instrument panel junction block assembly) and engine switch or the engine switch is defective
  1. Engine switch
  2. Main body ECU (instrument panel junction block assembly)
  3. Wire harness or connector

WIRING DIAGRAM

B157543E08

INSPECTION PROCEDURE

HINT:
When the main body ECU (instrument panel junction block assembly) is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.

After the main body ECU (instrument panel junction block assembly) is replaced, perform the registration procedures for the engine immobiliser system.

1. READ VALUE USING INTELLIGENT TESTER (START SWITCH)
  1. Turn the engine switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    St SW1
    Start Switch 1 / ON or OFF
    ON: Engine switch is pushed
    OFF: Engine switch is not pushed
    -
    St SW2
    Start Switch 2 / ON or OFF
    ON: Engine switch is pushed
    OFF: Engine switch is not pushed
    -

    OK:
    ON (engine switch is pushed) and OFF (engine switch is not pushed) appear on the screen.



NG
Go to step 3
OK


2. CHECK ENGINE SWITCH CONDITION
  1. Check the power source mode change.

    1. When the key is inside the vehicle and the shift lever is in the P position, check that pressing the engine switch causes the power source mode to change as follows:

      OK:
      off → on (ACC) → on (IG) → off



NG
GO TO PROBLEM SYMPTOMS TABLE (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. INSPECT ENGINE SWITCH

  1. Remove the engine switch (Click here).A109252E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    7 (SS1) - 5 (GND)
    Pushed
    Below 1 Ω
    2 (SS2) - 5 (GND)
    Pushed
    Below 1 Ω
    7 (SS1) - 5 (GND)
    Not pushed
    10 kΩ or higher
    2 (SS2) - 5 (GND)
    Not pushed
    10 kΩ or higher

    HINT:
    This switch is a momentary type switch.



NG
REPLACE ENGINE SWITCH (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - MAIN BODY ECU AND BODY GROUND)
  1. Disconnect the E7 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E52-7 (SS1) - E7-17 (SSW1)
    Always
    Below 1 Ω
    E52-2 (SS2) - E7-16 (SSW2)
    Always
    Below 1 Ω
    E52-5 (GND) - Body ground
    Always
    Below 1 Ω
    E52-7 (SS1) or E7-17 (SSW1) - Body ground
    Always
    10 kΩ or higher
    E52-2 (SS2) or E7-16 (SSW2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE SWITCH - MAIN BODY ECU AND BODY GROUND)
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


← B2277 Detecting Vehicle Submersion (from Jun 2009)B2281 "P" Signal Malfunction (from Jun 2009) →