2006-2011 Camry Aurion · Service Manual ENGINE

B2285 Steering Lock Position Signal Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Jun 2009

DESCRIPTION

This DTC is output when serial communication signals and LIN communication signals in the circuit between the main body ECU (instrument panel junction block assembly) and steering lock ECU (steering lock actuator) are inconsistent.
DTC No.
DTC Detection Condition
Trouble Area
B2285
Cable and LIN information between the main body ECU (instrument panel junction block assembly) and the steering lock ECU (steering lock actuator assembly) are inconsistent
  1. Main body ECU (instrument panel junction block assembly)
  2. Steering lock ECU (steering lock actuator assembly)
  3. Wire harness or connector

WIRING DIAGRAM

B233088E01

INSPECTION PROCEDURE

HINT:
When the main body ECU (instrument panel junction block assembly) is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
After the main body ECU (instrument panel junction block assembly) or steering lock ECU (steering lock actuator assembly) is replaced, perform the registration procedures for the engine immobiliser system.


1. READ VALUE USING INTELLIGENT TESTER
  1. Turn the engine switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    HINT:
    When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.

    Main Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Str Unlock SW
    Steering lock condition / ON or OFF
    ON: Steering is unlocked (Engine switch on (ACC))
    OFF: Steering is locked (Engine switch off)
    -

    OK:
    ON (steering is unlocked) and OFF (steering is locked) appear on the screen.



NG
Go to step 3
OK


2. CHECK FOR DTCS
  1. Clear the DTCs (Click here).

  1. Check for DTC B2285 (Steering lock position signal circuit malfunction), DTC B2287 (LIN communication master malfunction) and DTC B2785 (Communication malfunction between ECUs connected by LIN).

    Result:
    Display (DTC output)
    Proceed to
    "DTC B2285" only
    A
    "DTC B2287" and/or "DTC B2785"
    B
    No DTC
    C

    HINT:
    1. If DTC B2287 is output (Click here).
    2. If DTC B2785 is output (Click here).



B
GO TO DTC CHART

C
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - STEERING LOCK ECU)
  1. Disconnect the E7, IR and E51 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E7-18 (SLP) - E51-4 (SLP1)
    Always
    Below 1 Ω
    IR-9 (LIN1) - E51-5 (LIN)
    Always
    Below 1 Ω
    E7-18 (SLP) or E51-4 (SLP1) - Body ground
    Always
    10 kΩ or higher
    IR-9 (LIN1) or E51-5 (LIN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU - STEERING LOCK ECU)
OK


4. CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) OPERATION
  1. After replacing the main body ECU (instrument panel junction block assembly) with a normally functioning ECU, check that the engine starts. Make sure the brake pedal is depressed and the shift position is P at this time.

  1. Check that the engine switch mode can be changed by pushing the engine switch.

    HINT:
    Without depressing the brake pedal, push the engine switch repeatedly. Engine switch mode should turn from off to on (ACC) to on (IG) and back to off. With the brake pedal depressed, push the engine switch repeatedly. Engine switch mode should turn to ENGINE START from any status.

    OK:
    Engine can start normally.



NG
REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
OK

END (MAIN BODY ECU WAS DEFECTIVE)


← B2284 Brake Signal Malfunction (from Jun 2009)B2286 Runnable Signal Malfunction (from Jun 2009) →