2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Rear Door UNLOCK Detection Switch RH Circuit

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – May 2009 from Jun 2009

DESCRIPTION

The rear right door unlock detection switch is built into the rear right side door lock assembly. The switch turns on when the rear right door is unlocked and turns off when the door is locked.
The main body ECU is connected to the rear right door lock assembly via terminal LSWP (*1) or LSWR (*2) and rear right door lock/unlock state signals are input to the ECU.
The main body ECU applies voltage to the door unlock detection switch via terminal LSWP (*1) or LSWR (*2). When the door unlock detection switch is on (there is continuity between the switch terminals), an unlock state signal is input to the ECU. When the switch is off (there is no continuity between the switch terminals), a lock state signal is input.
  1. *1: without Smart Entry and Start System
  2. *2: with Smart Entry and Start System

WIRING DIAGRAM

B150881E03

INSPECTION PROCEDURE


1. SYSTEM CHECK
  1. Check the vehicle specification.

    Result:
    Result
    Proceed to
    with Smart Entry and Start System
    A
    without Smart Entry and Start System
    B



B
Go to step 3
A


2. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR-Door Lock Pos SW
    Rear right door lock position switch signal/ON or OFF
    ON: Rear right door lock is in UNLOCK position
    OFF: Rear right door lock is in LOCK position
    -

    OK:
    On the intelligent tester screen, the item changes between ON and OFF according to the chart above.



NG
Go to step 3
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

3. INSPECT REAR DOOR LOCK ASSEMBLY (UNLOCK DETECTION SWITCH)

  1. E123891E02
    Remove the rear door lock assembly RH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Measurement Condition
    Door Lock Condition
    Specified Condition
    6 - 9
    Battery positive (+) → Terminal 4
    Battery negative (-) → Terminal 1
    Locked
    10 kΩ or higher
    6 - 9
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 4
    Unlocked
    Below 1 Ω



NG
REPLACE REAR DOOR LOCK ASSEMBLY
OK


4. CHECK WIRE HARNESS (REAR DOOR LOCK - MAIN BODY ECU (INSTRUMENT PANEL J/B))

  1. Disconnect the rear door lock assembly RH connector.B138095E04

  1. Disconnect the main body ECU (instrument panel J/B) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    with Smart Entry and Start System 
    Tester Connection (Symbols)
    Condition
    Specified Condition
    J5-6 (LSSR) - E6-5 (LSWR)
    Always
    Below 1 Ω
    J5-6 (LSSR) - Body ground
    Always
    10 kΩ or higher
    J5-9 (E) - Body ground
    Always
    Below 1 Ω

    Standard resistance:
    without Smart Entry and Start System 
    Tester Connection (Symbols)
    Condition
    Specified Condition
    J5-6 (LSSR) - E6-27 (LSWP)
    Always
    Below 1 Ω
    J5-6 (LSSR) - Body ground
    Always
    10 kΩ or higher
    J5-9 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL J/B)


← Rear Door UNLOCK Detection Switch RH Circuit (Jun 2006 – May 2009)Driver Side Door Lock Motor Circuit (from Jun 2006) →