2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Illumination Circuit

Circuit diagnosis · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

Power is supplied to the radio receiver and steering pad switch illumination when the light control switch is in the TAIL or HEAD position.

WIRING DIAGRAM

E134726E05

INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (Click here).


1. CHECK ILLUMINATION
  1. Check if the illumination for the radio receiver, steering pad switch, glove box or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the HEAD or TAIL position.

    Result:
    Result
    Proceed to
    Illumination comes on for all components except steering pad switch.
    A
    Illumination comes on for all components except radio receiver.
    B
    No illumination comes on (radio receiver, hazard switch, glove box, etc.).
    C



B
Go to step 6

C
GO TO LIGHTING SYSTEM
A


2. CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE)

  1. E120026E21
    Disconnect the spiral cable connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester connection
    Condition
    Specified condition
    E18-12 (IL+2) - Body ground
    Light control switch TAIL or HEAD
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Disconnect the steering pad switch connector.

  1. Connect the positive (+) lead to terminal IL+2 and the negative (-) lead to terminal EAU of the steering pad switch assembly connector.E136205E03

  1. Check if the illumination for the steering pad switch assembly comes on.

    OK:
    Illumination for the steering pad switch assembly comes on.



NG
REPLACE STEERING PAD SWITCH ASSEMBLY
OK


4. INSPECT SPIRAL CABLE

  1. I039337E60
    Disconnect the steering pad switch and spiral cable connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Spiral Cable Position
    Specified condition
    a1-8 (EAU) - E18-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    a1-5 (IL+2) - E18-12 (IL+2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the pages shown in the brackets below.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)



NG
REPLACE SPIRAL CABLE
OK


5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)

  1. E131856E06
    Disconnect the connectors from the radio receiver and spiral cable.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    F8-6 (SWG) - E18-4 (EAU)
    Always
    Below 1 Ω
    F8-6 (SWG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

6. CHECK HARNESS AND CONNECTOR (BATTERY - RADIO RECEIVER)

  1. E136203E01
    Disconnect the radio receiver connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester connection
    Condition
    Specified condition
    F6-10 (ILL+) - Body ground
    Light control switch TAIL or HEAD
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - BODY GROUND)

  1. E136203E02
    Disconnect the radio receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    F6-7 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE


← Illumination Circuit (Jun 2006 – Sep 2006)Illumination Circuit (from Jun 2009) →