Illumination Circuit
Circuit diagnosis · Vehicles built Jun 2006 – Sep 2006
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
Power is supplied to the radio receiver and steering pad switch illumination when the light control switch is in the TAIL or HEAD position.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (Click here).
| 1. CHECK ILLUMINATION |
Check if the illumination for the radio receiver, steering pad switch, glove box or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the HEAD or TAIL position.
- Result:
Result
Proceed to
Illumination comes on for all components except steering pad switch.
A
Illumination comes on for all components except radio receiver.
B
No illumination comes on (radio receiver, hazard switch, glove box, etc.).
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE) |
Disconnect the spiral cable connector.

Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester connection
Condition
Specified condition
E18-12 (IL+2) - Body ground
Light control switch TAIL or HEAD
10 to 14 V
|
|
||||
| OK | |
| 3. INSPECT STEERING PAD SWITCH ASSEMBLY |
Disconnect the steering pad switch connector.
Connect the positive (+) lead to terminal IL+2 and the negative (-) lead to terminal EAU of the steering pad switch assembly connector.


Check if the illumination for the steering pad switch assembly comes on.
- OK:
- Illumination for the steering pad switch assembly comes on.
|
|
||||
| OK | |
| 4. INSPECT SPIRAL CABLE |
Disconnect the steering pad switch and spiral cable connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester connection
Spiral Cable Position
Specified condition
a1-8 (EAU) - E18-4 (EAU)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
a1-5 (IL+2) - E18-12 (IL+2)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
- NOTICE:
- The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the pages shown in the brackets below.
- HINT:
- Removal (Click here)
- Installation (Click here)
- Removal (Click here)
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - RADIO RECEIVER) |
Disconnect the connectors from the radio receiver and spiral cable.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester connection
Condition
Specified condition
F8-6 (SWG) - E18-4 (EAU)
Always
Below 1 Ω
F8-6 (SWG) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 6. CHECK HARNESS AND CONNECTOR (BATTERY - RADIO RECEIVER) |
Disconnect the radio receiver connector.

Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester connection
Condition
Specified condition
F6-10 (ILL+) - Body ground
Light control switch TAIL or HEAD
10 to 14 V
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - BODY GROUND) |
Disconnect the radio receiver connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester connection
Condition
Specified condition
F6-7 (GND) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
