2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Speaker Circuit

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – May 2009 from Jun 2009

DESCRIPTION

w/o Stereo Component Amplifier:
  1. If there is a short in this circuit, the radio receiver detects it and stops output to the speakers.
  2. Thus sound cannot be heard from the speakers even if there is no malfunction in the radio receiver or speakers.
  3. If a short is detected in the speaker circuit, no sound can be heard from the speakers.
w/ Stereo Component Amplifier:
  1. If there is a short in this circuit, the stereo component amplifier or radio receiver detects it and stops output to the speakers.
  2. Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier, radio receiver or speakers.
  3. If a short is detected in the speaker circuit, no sound can be heard from the speakers.

WIRING DIAGRAM


w/o Stereo Component Amplifier
E136201E03

w/ Stereo Component Amplifier
E192410E01

INSPECTION PROCEDURE


1. CONFIRM MODEL

Result:
Result
Proceed to
w/o Stereo Component Amplifier
A
w/ Stereo Component Amplifier
B



B
Go to step 7
A


2. CHECK HARNESS AND CONNECTOR
  1. Disconnect the radio receiver and speaker connectors.

  1. for 6 Speakers:Measure the resistance between each of the front No. 2 speakers and the radio receiver to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F6-2 (FL+) - F21-2 (TWL+)
    Always
    Below 1 Ω
    F6-6 (FL-) - F21-4 (TWL-)
    Always
    Below 1 Ω
    F6-1 (FR+) - F23-2 (TWR+)
    Always
    Below 1 Ω
    F6-5 (FR-) - F23-4 (TWR-)
    Always
    Below 1 Ω

  1. for 6 Speakers:Measure the resistance between each of the front No. 1 speakers and front No. 2 speakers to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F21-1 (+) - I1-1
    Always
    Below 1 Ω
    F21-3 (-) - I1-2
    Always
    Below 1 Ω
    F23-1 (+) - H1-1
    Always
    Below 1 Ω
    F23-3 (-) - H1-2
    Always
    Below 1 Ω

  1. for 4 Speakers:Measure the resistance between each of the front No. 1 speakers and radio receiver to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F6-2 (FL+) - I1-1
    Always
    Below 1 Ω
    F6-6 (FL-) - I1-2
    Always
    Below 1 Ω
    F6-1 (FR+) - H1-1
    Always
    Below 1 Ω
    F6-5 (FR-) - H1-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the rear speakers and the radio receiver to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F7-2 (RL+) - O12-1
    Always
    Below 1 Ω
    F7-6 (RL-) - O12-2
    Always
    Below 1 Ω
    F7-1 (RR+) - O13-1
    Always
    Below 1 Ω
    F7-3 (RR-) - O13-2
    Always
    Below 1 Ω

  1. Measure the resistance between the radio receiver and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F6-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    F6-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    F6-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    F6-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    F7-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    F7-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    F7-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    F7-3 (RR-) - Body ground
    Always
    10 kΩ or higher

  1. for 6 Speakers: Measure the resistance between each of the front No. 2 speakers and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F21-1 (+) - Body ground
    Always
    10 kΩ or higher
    F21-3 (-) - Body ground
    Always
    10 kΩ or higher
    F23-1 (+) - Body ground
    Always
    10 kΩ or higher
    F23-3 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT FRONT NO. 1 SPEAKER

  1. E165683E42
    Resistance check
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I1-1 - I1-2
      Always
      3.2 to 4.8 Ω
      H1-1 - H1-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *1
      Component without harness connected
      (Front No. 1 Speaker)



NG
REPLACE FRONT NO. 1 SPEAKER
OK


4. INSPECT REAR SPEAKER

  1. E104053E01
    Resistance check
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O12-1 - O12-2
      Always
      3.2 to 4.8 Ω
      O13-1 - O13-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *1
      Component without harness connected
      (Rear Speaker)



NG
REPLACE REAR SPEAKER
OK


5. CONFIRM MODEL

Result:
Result
Proceed to
for 6 Speakers
A
for 4 Speakers
B



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
A


6. INSPECT FRONT NO. 2 SPEAKER
  1. Check that the malfunction disappears when a known good speaker is installed (Click here).

    OK:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speakers that were disconnected.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
OK

END (FRONT NO. 2 SPEAKER WAS DEFECTIVE)

7. CHECK HARNESS AND CONNECTOR
  1. Disconnect the radio receiver, stereo component amplifier and speaker connectors.

  1. Measure the resistance between each of the front No. 2 speakers and the radio receiver to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F6-2 (FL+) - F47-2 (TWL+)
    Always
    Below 1 Ω
    F6-6 (FL-) - F47-4 (TWL-)
    Always
    Below 1 Ω
    F6-1 (FR+) - F48-2 (TWR+)
    Always
    Below 1 Ω
    F6-5 (FR-) - F48-4 (TWR-)
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 2 speakers and the stereo component amplifier to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F47-1 (+) - F46-1 (RL+)
    Always
    Below 1 Ω
    F47-3 (-) - F46-6 (RL-)
    Always
    Below 1 Ω
    F48-1 (+) - F46-2 (RR+)
    Always
    Below 1 Ω
    F48-3 (-) - F46-7 (RR-)
    Always
    Below 1 Ω

  1. Measure the resistance between each of the rear speakers and the radio receiver to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F7-2 (RL+) - O12-1
    Always
    Below 1 Ω
    F7-6 (RL-) - O12-2
    Always
    Below 1 Ω
    F7-1 (RR+) - O13-1
    Always
    Below 1 Ω
    F7-3 (RR-) - O13-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 1 speakers and the stereo component amplifier to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I1-1 - F46-4 (WFL+)
    Always
    Below 1 Ω
    I1-2 - F46-11 (WFL-)
    Always
    Below 1 Ω
    H1-1 - F46-3 (WFR+)
    Always
    Below 1 Ω
    H1-2 - F46-8 (WFR-)
    Always
    Below 1 Ω

  1. Measure the resistance between each speaker and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F47-1 (+) - Body ground
    Always
    10 kΩ or higher
    F47-3 (-) - Body ground
    Always
    10 kΩ or higher
    F47-2 (TWL+) - Body ground
    Always
    10 kΩ or higher
    F47-4 (TWL-) - Body ground
    Always
    10 kΩ or higher
    F48-1 (+) - Body ground
    Always
    10 kΩ or higher
    F48-3 (-) - Body ground
    Always
    10 kΩ or higher
    F48-2 (TWR+) - Body ground
    Always
    10 kΩ or higher
    F48-4 (TWR-) - Body ground
    Always
    10 kΩ or higher
    O12-1 - Body ground
    Always
    10 kΩ or higher
    O12-2 - Body ground
    Always
    10 kΩ or higher
    O13-1 - Body ground
    Always
    10 kΩ or higher
    O13-2 - Body ground
    Always
    10 kΩ or higher
    I1-1 - Body ground
    Always
    10 kΩ or higher
    I1-2 - Body ground
    Always
    10 kΩ or higher
    H1-1 - Body ground
    Always
    10 kΩ or higher
    H1-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. INSPECT FRONT NO. 1 SPEAKER

  1. E165683E42
    Resistance check
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I1-1 - I1-2
      Always
      1.6 to 2.4 Ω
      H1-1 - H1-2
      Always
      1.6 to 2.4 Ω

      Text in Illustration 
      *1
      Component without harness connected
      (Front No. 1 Speaker)



NG
REPLACE FRONT NO. 1 SPEAKER
OK


9. INSPECT FRONT NO. 2 SPEAKER
  1. Check that the malfunction disappears when a known good speaker is installed (Click here).

    OK:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speakers that were disconnected.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
Go to step 10
OK

END (FRONT NO. 2 SPEAKER WAS DEFECTIVE)

10. INSPECT REAR SPEAKER
  1. Check that the malfunction disappears when a known good speaker is installed (Click here).

    OK:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the rear speakers that were disconnected.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
OK

END (REAR SPEAKER WAS DEFECTIVE)


← Speaker Circuit (Jun 2006 – May 2009)Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter (from Jun 2009) →