2006-2011 Camry Aurion · Service Manual ENGINE

Cranking Holding Function Circuit

Circuit diagnosis · Vehicles built from Jun 2009

DESCRIPTION

  1. Vehicles with the SMART ENTRY AND START SYSTEM are equipped with the cranking holding control system.
  2. The cranking holding control system keeps energizing the ST relay after the ECM detects the starter signal (STSW signal) from the main body ECU until the ECM performs a judgment of "Engine started". Furthermore, the ECM outputs an accessory cut signal (ACCR signal) to the ACC relay during cranking to prevent flickering of the combination meter, clock, audio system, and so on.
    When the ECM detects the STSW signal, the ECM outputs the starter relay drive signal (STAR signal) to the starter relay through the park/neutral position switch, and then the engine is cranked. When the ECM receives a stable engine speed signal (NE signal), more specifically when the NE signal reaches a predetermined value, the ECM stops outputting the STAR signal. Also, the ECM monitors the ST relay operating conditions based on the STA terminal voltage status.
A145847E03

WIRING DIAGRAM

A132349E03

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the engine switch is turned on (IG).

  1. Check the result when the engine starts.

    Standard:
    Engine Switch
    Tester Display (Starter Signal)
    On (IG)
    OFF
    Engine start
    ON



OK
Go to step 10
NG


2. INSPECT ECM (STSW TERMINAL VOLTAGE)

  1. A115671E53
    Disconnect the A24 ECM connector.

  1. Move the shift lever to the P position.

  1. Measure the voltage between the ECM terminal and the body ground when engine is cranking.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    STSW (A24-14) - Body ground
    Cranking
    10 to 14 V

  1. Reconnect the ECM connector.



NG
Go to step 5
OK


3. INSPECT ECM (STAR OUTPUT VOLTAGE)

  1. A107891E07
    Disconnect the C1 Park/Neutral Position (PNP) switch connector.

  1. Measure the voltage between the terminal of the PNP switch connector and body ground while cranking the engine.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    B (C1-4) - Body ground
    Cranking
    10 to 14 V

  1. Reconnect the PNP switch connector.



NG
Go to step 6
OK


4. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. A107908E10
    Disconnect the C1 PNP switch connector.

  1. Measure the resistance when the transaxle gear selector lever is moved to each position.

    Standard resistance:
    Gear Selector
    Lever Position
    Tester Connection
    Specified Condition
    P
    2 - 6, 4 - 5
    Below 1 Ω
    R
    1 - 2
    N
    2 - 9, 4 - 5
    D
    2 - 7
    2
    2 - 3
    L
    2 - 8

  1. Reconnect the PNP switch connector.



OK
Go to step 10
NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)

5. CHECK HARNESS AND CONNECTOR (ECM - MAIN BODY ECU)

  1. A132357E01
    Disconnect the E9 main body ECU connector.

  1. Disconnect the A24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    STSW (E9-4) - STSW (A24-14)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    STSW (E9-4) or STSW (A24-14) - Body ground
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK SMART ENTRY AND START SYSTEM (Click here)

6. INSPECT ST CUT RELAY

  1. B016200E02
    Remove the ST CUT relay from the engine room R/B.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (When battery voltage applied between terminals 1 and 2)

  1. Reinstall the relay.



NG
REPLACE ST CUT RELAY
OK


7. INSPECT ENGINE ROOM R/B (ST CUT RELAY HOLDER TERMINAL VOLTAGE)

  1. A137045E04
    Remove the ST CUT relay from the engine room R/B.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    2 (+) - 1 (-)
    10 to 14 V

  1. Reinstall the relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST CUT RELAY, ST CUT RELAY - BODY GROUND)
OK


8. CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH - MAIN BODY ECU)

  1. A132358E02
    Remove the ST CUT relay from the engine room R/B.

  1. Disconnect the C1 PNP switch assembly connector.

  1. A132359E01
    Disconnect the E7 and E9 main body ECU connectors.

  1. Disconnect the C24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    ST CUT relay (3) - NSW (C24-52)
    Below 1 Ω
    ST CUT relay (3) - STR2 (E9-6)
    Below 1 Ω
    STR (E7-8) - ST CUT relay (5)
    Below 1 Ω
    B (C1-4) - ST CUT relay (5)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    ST CUT relay (3) - Body ground
    10 kΩ or higher
    ST CUT relay (5) - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the main body ECU connectors.

  1. Reconnect the PNP switch assembly connector.

  1. Reinstall the ST CUT relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. CHECK SMART ENTRY AND START SYSTEM
  1. Check SMART ENTRY AND START SYSTEM (Click here).

    OK:
    System is OK.



NG
REPAIR SMART ENTRY AND START SYSTEM (Click here)
OK

REPLACE ECM (Click here)

10. INSPECT ST RELAY

  1. B016200E02
    Remove the ST relay from the engine room R/B.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (When battery voltage applied between terminals 1 and 2)

  1. Reinstall the ST relay.



NG
REPLACE ST RELAY
OK


11. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ST RELAY)
A142642E02
  1. Remove the ST relay from the engine room R/B.

  1. Disconnect the C1 PNP switch assembly connector.

  1. Disconnect the A24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    L (C1-5) - STA (A24-48)
    Below 1 Ω
    L (C1-5) - ST relay (1)
    Below 1 Ω
    ST relay (2) - Body ground
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    L (C1-5) - Body ground
    10 kΩ or higher

  1. Reinstall the ST relay.

  1. Reconnect the PNP switch assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12. INSPECT STARTER ASSEMBLY
  1. Inspect the starter assembly (Click here).



NG
REPLACE STARTER ASSEMBLY (Click here)
OK


13. INSPECT BATTERY
  1. Check that the battery is not depleted.

    OK:
    Battery is not depleted.



NG
REPLACE BATTERY
OK


14. CHECK BATTERY TERMINAL
  1. Check that the battery terminals are not loose or corroded.

    OK:
    Battery terminals are not loose or corroded.



NG
REPAIR OR REPLACE BATTERY TERMINAL
OK

CHECK AND REPAIR STARTER POWER SOURCE CIRCUIT


← Fuel Injector Circuit (from Jun 2009)MIL Circuit (Jun 2006 – Sep 2006) →