2006-2011 Camry Aurion · Service Manual ENGINE

B2273 Ignition 2 Monitor Malfunction

Diagnostic trouble codes · Vehicles built from Jun 2009

DESCRIPTION

This DTC is output when there is a problem in the IG2D output circuit, which is from the inside of the main body ECU (instrument panel junction block assembly) to the IG2 relay.
DTC No.
DTC Detection Condition
Trouble Area
B2273
IG2 relay actuation circuit inside main body ECU (instrument panel junction block assembly) or other related circuit is malfunctioning
  1. IG2 relay
  2. Main body ECU (instrument panel junction block assembly)
  3. Wire harness or connector

WIRING DIAGRAM

B157541E05

INSPECTION PROCEDURE

HINT:
When the main body ECU (instrument panel junction block assembly) is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
After the main body ECU (instrument panel junction block assembly) is replaced, perform the registration procedures for the engine immobiliser system.


1. READ VALUE USING INTELLIGENT TESTER
  1. Turn the engine switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    HINT:
    When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.

    Main Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG2 Relay Mon1
    Status of IG2 relay monitor (outer) / ON or OFF
    ON: Engine switch on (IG) (IG2 relay is ON)
    OFF: Engine switch off (IG2 relay is OFF)
    -

    Result:
    Result
    Proceed to
    "ON" (engine switch on (IG)) appears on the screen.
    B
    "ON" (engine switch on (IG)) does not appear on the screen.
    A



B
Go to step 3
A


2. CHECK ENGINE SWITCH CONDITION
  1. Check the power source mode change.

    1. When the key is inside the vehicle and the shift lever is in the P position, check that pressing the engine switch causes the power source mode to change as follows:

      OK:
      off → on (ACC) → on (IG) → off



NG
GO TO PROBLEM SYMPTOMS TABLE (Click here)
OK


3. INSPECT RELAY (IG2 RELAY)

  1. B060778E89
    Remove the IG2 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied to terminals between 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage is applied to terminals between 1 and 2
    Below 1 Ω



NG
REPLACE RELAY
OK


4. CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - MAIN BODY ECU AND BODY GROUND)
  1. Remove the IG2 relay from the engine room relay block.

  1. Disconnect the E6 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Engine Room Relay Block IG2 relay terminal 1 - E6-11 (IG2D)
    Always
    Below 1 Ω
    Engine Room Relay Block IG2 relay terminal 2 - Body ground
    Always
    Below 1 Ω
    E6-11 (IG2D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM RELAY BLOCK - MAIN BODY ECU AND BODY GROUND)
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


← B2272 Ignition 1 Monitor Malfunction (from Jun 2009)B2274 ACC Monitor Malfunction (from Jun 2009) →