B2272 Ignition 1 Monitor Malfunction
Diagnostic trouble codes · Vehicles built from Jun 2009
DESCRIPTION
This DTC is output when there is a problem in the IG1D output circuit, which is from the inside of the main body ECU (instrument panel junction block assembly) to the IG1 relay.| DTC No. |
DTC Detection Condition |
Trouble Area |
| B2272 |
IG1 relay actuation circuit inside main body ECU (instrument panel junction block assembly) or other related circuit is malfunctioning |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- When the main body ECU (instrument panel junction block assembly) is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
- After the main body ECU (instrument panel junction block assembly) is replaced, perform the registration procedures for the engine immobiliser system.
| 1. READ VALUE USING INTELLIGENT TESTER |
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
- HINT:
- When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.
Main Body: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
IG1 Relay Mon1
Status of IG1 relay monitor (outer) / ON or OFF
ON: Engine switch on (IG) (IG1 relay is ON)
OFF: Engine switch off (IG1 relay is OFF)
-
- Result:
Result
Proceed to
"ON" (engine switch on (IG)) appears on the screen.
A
"ON" (engine switch on (IG)) does not appear on the screen.
B
|
|
||||
| A | |
| 2. CHECK ENGINE SWITCH CONDITION |
Check the power source mode change.
When the key is inside the vehicle and the shift lever is in the P position, check that pressing the engine switch causes the power source mode to change as follows:
- OK:
- off → on (ACC) → on (IG) → off
|
|
||||
| OK | |
| 3. INSPECT RELAY (IG1 RELAY) |
Remove the IG1 relay from the instrument panel junction block.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 - 5
When battery voltage is not applied to terminals between 1 and 2
10 kΩ or higher
3 - 5
When battery voltage is applied to terminals between 1 and 2
Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - MAIN BODY ECU) |
Disconnect the Il junction block connector.
Disconnect the E7 ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
II-9 - E7-3 (IG1D)
Always
Below 1 Ω
E7-3 (IG1D) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - BATTERY AND BODY GROUND) |
Disconnect the IF and IA junction block connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
IF-10 - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
IA-1 - Body ground
Always
11 to 14 V
|
|
||||
| OK | |
| 6. INSPECT INSTRUMENT PANEL JUNCTION BLOCK |
Measure the resistance according to the value(s) in the table below.


- Standard Resistance:
Tester Connection
Condition
Specified Condition
IF-10 - Instrument Panel junction block IG1 relay terminal-1
Always
Below 1 Ω
Il-9 - Instrument Panel junction block IG1 relay terminal-2
Always
Below 1 Ω
IF-10 - Body ground
Always
10 kΩ or higher
Il-9 - Body ground
Always
10 kΩ or higher
Text in Illustration *1
Component without harness connected
(Instrument Panel Junction Block)
*2
IG1 Relay Terminal
|
|
||||
| OK | ||
| ||
