2006-2011 Camry Aurion · Service Manual ENGINE

B2273 Ignition 2 Monitor Malfunction

Diagnostic trouble codes · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

This DTC is output when there is a problem in the IG2D output circuit, which is from the inside of the main body ECU to the IG2 relay.

HINT:
When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
After the main body ECU is replaced, perform the registration procedures for the engine immobiliser system.

DTC No.
DTC Detection Condition
Trouble Area
B2273
IG2 relay actuation circuit inside main body ECU or other related circuit is malfunctioning
  1. Main body ECU
  2. IG2 relay
  3. Wire harness or connector

WIRING DIAGRAM

B157541E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the intelligent tester main switch on.

  1. Read the Data List according to the displays on the tester.

    HINT:
    When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.

    Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG2 Relay Mon1
    Status of IG2 relay monitor (outer) / ON or OFF
    ON: Engine switch on (IG) (IG2 relay is ON)
    OFF: Engine switch off (IG2 relay is OFF)
    -

    Result:
    Result
    Proceed to
    "ON" (engine switch on (IG)) appears on the screen.
    B
    "ON" (engine switch on (IG)) does not appear on the screen.
    A



B
Go to step 3
A


2. CHECK ENGINE SWITCH CONDITION
  1. Check the power source mode change.

    1. When the key is inside the vehicle and the shift lever is in the P position, check that pressing the engine switch causes the power source mode to change as follows:

      OK:
      off → on (ACC) → on (IG) → off

      HINT:
      1. If power mode does not change to ON (IG and ACC) (Click here).
      2. If power mode does not change to ON (IG) (Click here).
      3. If power mode does not change to ON (ACC) (Click here).



NG
GO TO OTHER PROBLEM
OK


3. INSPECT RELAY (IG2 RELAY)

  1. B060778E89
    Remove the IG2 relay from the engine room R/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE RELAY
OK


4. CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - MAIN BODY ECU AND BODY GROUND)

  1. Remove the IG2 relay from the engine room R/B.B138002E06

  1. Disconnect the E6 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Engine Room R/B IG2 relay terminal 1 - E6-11 (IG2D)
    Always
    Below 1 Ω
    Engine Room R/B IG2 relay terminal 2 - Body ground
    Always
    Below 1 Ω
    E6-11 (IG2D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← B2273 Ignition 2 Monitor Malfunction (Oct 2006 – May 2009)B2274 ACC Monitor Malfunction (Oct 2006 – May 2009) →