2006-2011 Camry Aurion · Service Manual ENGINE

B2274 ACC Monitor Malfunction

Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

This DTC is output when there is a problem in the ACCD output circuit, which is from the inside of the main body ECU to the ACC relay.

HINT:
When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
After the main body ECU is replaced, perform the registration procedures for the engine immobiliser system.

DTC No.
DTC Detection Condition
Trouble Area
B2274
ACC relay actuation circuit inside main body ECU or other related circuit is malfunctioning
  1. Main body ECU
  2. ACC relay
  3. Wire harness or connector

WIRING DIAGRAM

B162385E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the intelligent tester main switch on.

  1. Read the Data List according to the displays on the tester.

    HINT:
    When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.

    Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ACC Relay Mon
    Status of ACC Relay Monitor / ON or OFF
    ON: Engine switch on (ACC)
    OFF: Engine switch off
    -

    Result:
    Result
    Proceed to
    "ON" (engine switch on (ACC)) appears on the screen.
    B
    "ON" (engine switch on (ACC)) does not appear on the screen.
    A



B
Go to step 3
A


2. CHECK ENGINE SWITCH CONDITION
  1. Check the power source mode change.

    1. When the key is inside the vehicle and the shift lever is in the P position, check that pressing the engine switch causes the power source mode to change as follows:

      OK:
      off → on (ACC) → on (IG) → off

      HINT:
      1. If power mode does not change to ON (IG and ACC) (Click here).
      2. If power mode does not change to ON (IG) (Click here).
      3. If power mode does not change to ON (ACC) (Click here).



NG
GO TO OTHER PROBLEM
OK


3. INSPECT RELAY (ACC RELAY)

  1. A092673
    Remove the ACC relay from the instrument panel J/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE RELAY
OK


4. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - MAIN BODY ECU)

  1. Disconnect the E7 ECU connector.B138001E14

  1. Disconnect the II J/B connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    II-3 - E7-22 (ACCD)
    Always
    Below 1 Ω
    E7-22 (ACCD) or II-3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - BATTERY AND BODY GROUND)

  1. B157539E01
    Disconnect the IF and IA J/B connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    IF-10 - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    IA-1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT INSTRUMENT PANEL JUNCTION BLOCK

  1. Measure the resistance according to the value(s) in the table below.B157554E01

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Instrument Panel J/B ACC relay terminal 1 - IF-10
    Always
    Below 1 Ω
    Instrument Panel J/B ACC relay terminal 2 - II-3
    Always
    Below 1 Ω
    IF-10 - Body ground
    Always
    10 kΩ or higher
    II-3 - Body ground
    Always
    10 kΩ or higher



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK
OK

REPLACE MAIN BODY ECU


← B2273 Ignition 2 Monitor Malfunction (from Jun 2009)B2274 ACC Monitor Malfunction (from Jun 2009) →