2006-2011 Camry Aurion · Service Manual ENGINE

B2275 STSW Monitor Malfunction

Diagnostic trouble codes · Vehicles built from Jun 2009

DESCRIPTION

This DTC is output when there is an open, short, or any other problem in the engine start request output circuit inside the main body ECU (instrument panel junction block assembly) or in the external circuit.
DTC No.
DTC Detection Condition
Trouble Area
B2275
ST output circuit (engine starting request signal circuit) inside main body ECU (instrument panel junction block assembly) or other related circuit is malfunctioning
  1. ECM
  2. Main body ECU (instrument panel junction block assembly)
  3. Wire harness or connector

WIRING DIAGRAM

B232582E03

INSPECTION PROCEDURE

HINT:
When the main body ECU (instrument panel junction block assembly) is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
After the main body ECU (instrument panel junction block assembly) is replaced, perform the registration procedures for the engine immobiliser system.


1. CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

    HINT:
    After all DTCs are cleared, turn the engine switch on (IG) and depress the brake pedal. After 15 seconds have elapsed, check if the trouble occurs again.

  1. Check for DTCs again.

    OK:
    DTC is not output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK) - ECM)
  1. Disconnect the E9 connector.

  1. Disconnect the A24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E9-4 (STSW) - A24-14 (STSW)
    Always
    Below 1 Ω
    E9-4 (STSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK) - ECM)
OK


3. INSPECT MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

  1. B138004E31
    Reconnect the connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E9-4 (STSW) - Body ground
    Brake pedal depressed, Engine switch hold on (ST)
    Output voltage at terminal AM1 or AM2 is -2 V or more.

    Text in Illustration 
    *1
    Component with harness connected
    (Main Body ECU (Instrument Panel Junction Block Assembly))



NG
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
OK


4. CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) OPERATION
  1. After replacing the main body ECU (instrument panel junction block assembly) with a normally functioning ECU, check that the engine can start. Make sure the brake pedal is depressed and the shift position is P at this time.

  1. Check that the engine switch mode can be changed by pushing the engine switch.

    HINT:
    Without depressing the brake pedal, push the engine switch repeatedly. Engine switch mode should turn from off to on (ACC) to on (IG) and back to off. With the brake pedal depressed, push the engine switch repeatedly. Engine switch mode should turn to ENGINE START from any status.

    OK:
    Engine can start normally.

    HINT:
    If engine does not start (Click here).



NG
GO TO ENGINE CONTROL SYSTEM
OK

END (MAIN BODY ECU WAS DEFECTIVE)


← B2274 ACC Monitor Malfunction (from Jun 2009)B2276 ACCR Signal Circuit Malfunction (from Jun 2009) →