2006-2011 Camry Aurion · Service Manual ENGINE

Engine does not Start

Circuit diagnosis · Vehicles built from Jun 2009

DESCRIPTION


ENGINE START SYSTEM FUNCTION
  1. If the engine switch is pressed with the shift lever in the P or N position and the brake pedal depressed, the main body ECU (instrument panel junction block assembly) determines that it is an engine start request.

  2. The certification ECU (smart key ECU assembly) and other ECUs perform key verification via the LIN communication line.

  3. The main body ECU (instrument panel junction block assembly) activates the ACC relay.

  4. The main body ECU (instrument panel junction block assembly) activates the IG1 and IG2 relays.

  5. The certification ECU (smart key ECU assembly) outputs a steering UNLOCK signal. The signal is sent to the main body ECU (instrument panel junction block assembly) via the steering lock ECU (steering lock actuator assembly).

  6. The main body ECU (instrument panel junction block assembly) sends an engine start request signal to the ECM.

  7. The ECM sends an ACC cut request signal to the main body ECU (instrument panel junction block assembly).

  8. The ECM and main body ECU (instrument panel junction block assembly) activate the ST relay.

  9. The main body ECU (instrument panel junction block assembly) deactivates the ACC relay until the ECU detects an engine start.

  10. When engine revolution speed reaches 1200 rpm, the ECM determines that the engine has been started.
    The ECM stop sending on ACC cut request signal to the main body ECU (instrument panel junction block assembly).
    The main body ECU (instrument panel junction block assembly) reactivates the ACC relay and turns off the engine switch indicator light, when engine revolution speed reaches 800 rpm.

    Symbols of main body ECU (instrument panel junction block assembly)
    Signals
    STP
    Stop light switch ON signal
    Input
    SSW1/SSW2
    Engine switch ON signal
    Input
    ACCD
    ACC relay operation signal
    Output
    SLP
    Shift lock actuator position signal
    Input
    IG1D
    IG1 relay operation signal
    Output
    P
    Shift lock signal
    Input
    IG2D
    IG2 relay operation signal
    Output
    STR2
    ST relay operation signal (Sub)
    Output
    STR
    Park/neutral position switch signal
    Input
    TACH
    Engine start detection signal
    Input
    STSW
    Starter activation request signal
    Output
    ACCR
    ACC cut request signal
    Input
    Symbols of ECM
    Signals
    ACCR
    ACC cut request signal
    Output
    TACH
    Engine revolution speed signal
    Output
    STSW
    Starter activation request signal
    Input
    NSW
    Park/neutral position switch signal
    Input
    STAR
    ST relay operation signal (Main)
    Output
    STA
    Starter activation signal
    Input

B233079E01
B164718E13

WIRING DIAGRAM

See Cranking Holding Function Circuit (Click here).

INSPECTION PROCEDURE


EMERGENCY ENGINE START CONTROL
  1. If there is a malfunction in the stop light switch or STOP fuse, their signals may not be correctly transmitted to the main body ECU (instrument panel junction block assembly). This may result in the engine not starting even if the engine switch is pressed while the brake pedal is depressed and the shift lever is in the P position.
    To activate the starter:

    1. Turn the engine switch from off to on (ACC).

    2. Press and hold the engine switch for 15 seconds.

HINT:
After the main body ECU (instrument panel junction block assembly), certification ECU (smart key ECU assembly), steering lock ECU, ID code box (immobiliser code ECU) and/or ECM are/is replaced, perform the registration procedures for the engine immobiliser system.


1. CHECK ENTRY FUNCTION DETECTION AREA

  1. B137958E01
    Inspect entry detection area.
    1. When the electrical key is in either of the 2 inspection points in the illustration, the shift lever is in the P position and the brake pedal is depressed, check that the engine switch indicator illuminates in green.

      OK:
      Engine switch illuminates in green.

      HINT:
      If the engine switch does not illuminate, perform troubleshooting according to the Problem Symptoms Table of the smart entry and start system (starting) (engine switch indicator light does not come on) (Click here) and the smart entry and start system (entry door lock) (matching for the inside of the cabin cannot be performed) (Click here).



NG
GO TO OTHER PROBLEM
OK


2. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs again.

    OK:
    DTC is not output.

    HINT:
    1. If smart entry and start system (starting function) DTCs are output (Click here).
    2. If wireless door lock control system DTCs are output (Click here).
    3. If electrical steering lock DTCs are output (Click here).
    4. If engine immobiliser system DTCs are output (Click here).
    5. If engine control system DTCs output (2AZ-FE) (Click here).



NG
GO TO DTC CHART
OK


3. CHECK ENGINE SWITCH CONDITION
  1. Check the power source mode change.

    1. When the key is inside the vehicle and the shift lever is in the P position, check that pressing the engine switch causes the power source mode to change as follows:

      OK:
      off → on (ACC) → on (IG) → off

      HINT:
      1. If power mode does not change to ON (IG and ACC) (Click here).
      2. If power mode does not change to ON (IG) (Click here).
      3. If power mode does not change to ON (ACC) (Click here).



NG
GO TO OTHER PROBLEM
OK


4. CHECK CRANKING FUNCTION
  1. Check the engine cranking function.

    1. When there is fuel in the fuel tank, the key is inside the vehicle, and the shift lever is in the P position, check that depressing the brake pedal and pressing the engine switch crank the engine.

      Result:
      Result
      Proceed to
      Engine doesn't crank.
      A
      Engine cranks.
      B



B
Go to step 22
A


5. READ VALUE USING INTELLIGENT TESTER (P SIGNAL)
  1. Turn the engine switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Shift P Sig
    Shift P signal / ON or OFF
    ON: Shift position is P
    OFF: Shift position is not P
    -

    OK:
    ON (P signal is ON) and OFF (P signal is OFF) appear on the screen.

    HINT:
    If the result is not as specified, perform troubleshooting for DTC B2281 ("P" signal malfunction) first (Click here).



NG
GO TO DTC B2281 (Click here)
OK


6. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Read the Data List according to the display on the intelligent tester.

    Main Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light Switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

    OK:
    ON (brake pedal depressed) and OFF (brake pedal released) appear on the screen.

    HINT:
    If the result is not as specified, perform troubleshooting for DTC B2284 (Brake signal malfunction) first (Click here).



NG
GO TO DTC B2284 (Click here)
OK


7. READ VALUE USING INTELLIGENT TESTER (STEERING LOCK)
  1. Read the Data List according to the display on the intelligent tester.

    Main Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Str Unlock SW
    Steering lock condition / ON or OFF
    ON: Steering is unlocked (Engine switch on (ACC))
    OFF: Steering is locked (Engine switch off)
    -

    OK:
    ON (steering is unlocked) and OFF (steering is locked) appear on the screen.

    HINT:
    If the result is not as specified, perform troubleshooting for DTCs B2285 (Steering lock position signal circuit malfunction) and B2288 (Steering lock signal circuit malfunction) first (Click here).



NG
GO TO DTC B2285 (Click here)
OK


8. CHECK STEERING LOCK
  1. Check if the steering lock is released when turning the engine switch on (ACC).

    OK:
    The steering lock is released.



NG
Go to step 21
OK


9. INSPECT MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) (STSW VOLTAGE)

  1. B138004E32
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E9-4 (STSW) - Body ground
    Brake pedal depressed, engine switch held on (ST)
    Output voltage at terminal AM1 or AM2 is -2 V or more.

    Text in Illustration 
    *1
    Component with harness connected
    (Main Body ECU (Instrument Panel Junction Block Assembly))

    HINT:
    If the result is not as specified, perform troubleshooting for DTC B2275 (STSW monitor malfunction) first (Click here).



NG
GO TO DTC B2275 (Click here)
OK


10. INSPECT ECM (ACCR VOLTAGE)

  1. B138007E26
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E6-3 (ACCR) - Body ground
    Brake pedal depressed, shift lever P position, engine switch is pushed once → on (IG)
    0.1 to 0.8 V*1 → Output voltage at terminal AM1 or AM2 is -2 V or more.

    Text in Illustration 
    *1
    Component with harness connected
    (Main Body ECU (Instrument Panel Junction Block Assembly))
    *1: Voltage is output only when the engine is cranking.

    HINT:
    If the result is not as specified, perform troubleshooting for DTC B2276 (ACCR signal circuit malfunction) first (Click here).



NG
GO TO DTC B2276 (Click here)
OK


11. INSPECT MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) (STR VOLTAGE)

  1. B138007E24
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E7-8 (STR) - Body ground
    Shift lever P or N position → except P or N position
    Below 2 V → Pulse generation

    Text in Illustration 
    *1
    Component with harness connected
    (Main Body ECU (Instrument Panel Junction Block Assembly))

  1. Proceed to the next step based on the inspection result.

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 17
A


12. INSPECT RELAY (ST CUT)

  1. B016200E23
    Measure the resistance of the ST CUT relay.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE RELAY
OK


13. INSPECT PARK/NEUTRAL POSITION SWITCH

  1. B138018E25
    Disconnect the park/neutral position (PNP) switch connector.

  1. Measure the resistance according the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 - 9
    P
    Below 1 Ω
    4 - 9
    N
    Below 1 Ω
    4 - 9
    Except P and N
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Park/Neutral Position Switch)



NG
REPLACE PARK / NEUTRAL POSITION SWITCH (Click here)
OK


14. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM, MAIN BODY ECU)
  1. Disconnect the C24 connector.

  1. Remove ST CUT relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C24-52 (NSW) - C1-4
    Always
    Below 1 Ω
    C24-52 (NSW) - E7-8 (STR)
    Always
    Below 1 Ω
    C24-52 (NSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM, MAIN BODY ECU)
OK


15. INSPECT INSTRUMENT PANEL JUNCTION BLOCK (STR2 VOLTAGE)

  1. B138004E33
    Disconnect the C24 ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E9-6 (STR2) - Body ground
    Brake pedal depressed, shift lever P or N position, engine switch on (ST)
    Output voltage at terminal AM1 or AM2 is -3.5 V or more.*1

    Text in Illustration 
    *1
    Component with harness connected
    (Main Body ECU (Instrument Panel Junction Block Assembly))
    *1: Voltage is output for 0.3 seconds when the engine is cracking to start. Disconnect the C55 connector from the ECM before measuring the voltage.



NG
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
OK


16. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM - ENGINE ROOM RELAY BLOCK)
  1. Remove the ST CUT relay from the engine room relay block.

  1. Disconnect the E9 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C24-52 (NSW) - E9-6 (STR2)
    Always
    Below 1 Ω
    C24-52 (NSW) - ST CUT relay terminal - 3
    Always
    Below 1 Ω
    C24-52 (NSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU - ECM - ENGINE ROOM RELAY BLOCK)
OK


17. INSPECT RELAY (ST)

  1. B016200E23
    Remove the starter relay from the engine room relay block.

  1. Measure the resistance of the starter relay.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE RELAY
OK


18. CHECK HARNESS AND CONNECTOR (ECM - ST RELAY, PARK/NEUTRAL POSITION SWITCH)
  1. Disconnect the A24 ECM connector.

  1. Measure the resistance according the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-48 (STA) - Engine Room R/B ST relay terminal - 1
    Always
    Below 1 Ω
    A24-48 (STA) - C1-9
    Always
    Below 1 Ω
    A24-48 (STA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - ST RELAY, PARK/NEUTRAL POSITION SWITCH)
OK


19. INSPECT ENGINE ROOM RELAY BLOCK (ST RELAY VOLTAGE)

  1. B157569E03
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    ST relay terminal - 5 - Body ground
    Always
    11 to 14 V
    ST relay terminal - 2 - Body ground
    Always
    Below 1 V

    Text in Illustration 
    *1
    Component without relay connected
    (Engine Room Relay Block)
    *2
    ST Relay Terminal



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


20. INSPECT STARTER ASSEMBLY

HINT:
(Click here).



NG
REPAIR OR REPLACE STARTER ASSEMBLY
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER - BATTERY, ST RELAY)

21. READ VALUE USING INTELLIGENT TESTER (L CODE)
  1. Reconnect the connector.

  1. Turn the engine switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Entry & Start / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Entry & Start: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    L Code Chk
    L code check / ON or NG
    OK: Normal
    NG: Malfunction
    Electrical key in the cabin

    OK:
    OK is displayed on the screen.

    HINT:
    If the result is not as specified, refer to Problem Symptoms Table of the electrical steering lock (steering wheel cannot be unlocked) (Click here).
    If the result is not as specified, there may be a malfunction with the steering lock ECU or the ID code box (immobiliser code ECU).



NG
GO TO ELECTRIC STEERING LOCK (Click here)
OK


22. READ VALUE USING INTELLIGENT TESTER (ENGINE START REQUEST)
  1. Read the Data List according to the display on the intelligent tester.

    Entry & Start: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Start Rqst
    Start request signal response / OK or NG
    OK: Received
    NG: Not received
    -

    OK:
    OK (received) and NG (not received) appear on the screen.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


23. READ VALUE USING INTELLIGENT TESTER (S CODE)
  1. Read the Data List according to the display on the intelligent tester.

    HINT:
    When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.

  1. Turn the engine switch on (IG).

    Entry & Start: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    S Code Chk
    S code check / OK or NG
    OK: Normal
    NG: Malfunction
    -

    OK:
    OK is displayed on the screen.

    HINT:
    If the result is not as specified, there may be a malfunction with the certification ECU (smart key ECU assembly) or the ID code box (immobiliser code ECU).



NG
Go to step 25
OK


24. INSPECT ID CODE BOX (IMMOBILISER CODE ECU)

  1. B157556E08
    Check the input signal waveform.
    1. Connect an oscilloscope to terminal E50-6 (EFIO) and body ground.

    2. Turn the engine switch on (IG).

    3. Check the signal waveform according to the condition(s) in the table below.

      Item
      Condition
      Tool setting
      10 V/DIV., 100 ms./DIV.
      Vehicle condition
      Engine switch on (IG)
      Text in Illustration 
      *1
      Component without harness connected
      (ID Code Box (Immobiliser Code ECU))



NG
REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
OK

END

25. REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Replace the certification ECU (smart key ECU assembly).

  1. Perform the registration procedures for the engine immobiliser system.

  1. Check if the engine can be started.

    OK:
    Engine can be started.



OK
END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)
NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)


← B2289 Key Collation Waiting Time Over (from Jun 2009)Engine Switch Indicator Circuit (from Jun 2009) →