2006-2011 Camry Aurion · Service Manual RESTRAINTS

B1625/22 Front Passenger Side - Side Airbag Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The front passenger side - side airbag sensor circuit consists of the center airbag sensor assembly, side airbag sensor LH, and rear airbag sensor LH.
If the center airbag sensor assembly receives signals from the side airbag sensor LH and rear airbag sensor LH, it determines whether or not the SRS should be activated.
DTC B1625/22 is recorded when a malfunction is detected in the front passenger side - side airbag sensor circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1625/22
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front passenger side - side airbag sensor circuit for 2 seconds.
  2. Side airbag sensor LH malfunction
  3. Rear airbag sensor LH malfunction
  4. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Side airbag sensor LH
  3. Rear airbag sensor LH
  4. Center airbag sensor assembly

WIRING DIAGRAM

H045218E11

INSPECTION PROCEDURE


1. CHECK DTC

  1. C123698E06
    Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1625/22 is not output.

    HINT:
    Codes other than DTC B1625/22 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK (Click here)
NG


2. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS, THEN GO TO STEP 1
OK


3. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly and side airbag sensor LH.

  1. Check that the connectors (on the center airbag sensor assembly side and side airbag sensor LH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE FLOOR WIRE
OK


4. CHECK FLOOR WIRE (OPEN)

  1. C114846E10
    Using a service wire, connect terminals 8 (BBP+) and 11 (BBP-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N7-4 (BBL+) - N7-3 (BBL-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK


5. CHECK FLOOR WIRE (SHORT)

  1. C114847E12
    Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N7-4 (BBL+) - N7-3 (BBL-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


6. CHECK FLOOR WIRE (SHORT TO B+)

  1. C114847E12
    Connect the negative (-) terminal cable from the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    N7-4 (BBL+) - Body ground
    Ignition switch ON
    Below 1 V
    N7-3 (BBL-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE
OK


7. CHECK FLOOR WIRE (SHORT TO GROUND)

  1. C114847E12
    Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N7-4 (BBL+) - Body ground
    Always
    1 MΩ or higher
    N7-3 (BBL-) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


8. CONFIRM PART NUMBER OF SIDE AIRBAG SENSOR
  1. Check that the part number of the side airbag sensor LH is equal to the number of the other side.

    OK:
    Those numbers are the same.

  1. Connect the connectors to the center airbag sensor assembly and side airbag sensor LH.



NG
Go to step 10
OK


9. CHECK SIDE AIRBAG SENSOR LH

  1. C123699E07
    Interchange the side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1620/21 and B1625/22 are not output.
    A
    DTC B1625/22 is output.
    B
    DTC B1620/21 is output.
    C

    HINT:
    Codes other than DTC B1620/21 and B1625/22 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



B
Go to step 11

C
REPLACE SIDE AIRBAG SENSOR LH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

10. REPLACE SIDE AIRBAG SENSOR LH

  1. C123698E06
    Replace the side airbag sensor LH (Click here).

    HINT:
    Perform inspection using parts from a normal vehicle if possible.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1625/22 is not output.

HINT:
Codes other than DTC B1625/22 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.



OK
END
NG


11. CHECK CONNECTION OF CONNECTOR
  1. Check that the connector is properly connected to the rear airbag sensor LH.

    OK:
    The connector is properly connected.



NG
CONNECT CONNECTOR
OK


12. CHECK CONNECTOR
  1. Disconnect the connector from the rear airbag sensor LH.

  1. Check that the connector (on the rear airbag sensor LH side) is not damaged.

    OK:
    The connector is not deformed or damaged.



NG
REPAIR OR REPLACE FLOOR WIRE
OK


13. CHECK FLOOR WIRE (OPEN)
  1. Disconnect the connector from the side airbag sensor LH.

  1. C114836E15
    Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N7-1 (BCL+) - N7-2 (BCL-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK


14. CHECK FLOOR WIRE (SHORT)

  1. C114843E11
    Disconnect the service wire from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N7-1 (BCL+) - N7-2 (BCL-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


15. CHECK FLOOR WIRE (SHORT TO B+)

  1. C114843E11
    Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    N7-1 (BCL+) - Body ground
    Ignition switch ON
    Below 1 V
    N7-2 (BCL-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE
OK


16. CHECK FLOOR WIRE (SHORT TO GROUND)

  1. C114843E11
    Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N7-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    N7-2 (BCL-) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


17. CHECK REAR AIRBAG SENSOR LH

  1. C142520E03
    Connect the connector to the side airbag sensor LH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1625/22 is output.

    HINT:
    Codes other than DTC B1625/22 may be output at this time, but they are not related to this check.



NG
REPLACE REAR AIRBAG SENSOR LH (Click here)
OK


18. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. C142515E06
    Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connector to the rear airbag sensor LH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1625/22 is not output.

    HINT:
    Codes other than DTC B1625/22 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1620/21 Driver Side - Side Airbag Sensor Circuit Malfunction (from Jun 2009)B1625/22 Front Passenger Side - Side Airbag Sensor Circuit Malfunction (Oct 2006 – May 2009) →