2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

INSTALLATION

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. INSTALL CENTER STOP LIGHT SET (w/o Rear Sunshade)

  1. E128222
    Connect the connector.

  1. Install the center stop light set with the 2 screws.


2. INSTALL CENTER STOP LIGHT ASSEMBLY (w/ Rear Sunshade)

  1. E138991
    Engage the 4 claws and install the center stop light assembly.


3. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade)

  1. B132022
    without Rear Spoiler:

    1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

    2. Engage the 4 clips and 5 claws and install the package tray trim panel assembly.

    3. Connect the connector.

  1. B153040
    with Rear Spoiler:

    1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

    2. Engage the 4 clips and 5 claws and install the package tray trim panel assembly.


4. INSTALL NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)
  1. Connect the connector.

  1. B152699
    Engage the 5 claws and 4 clips, and install the No. 2 package tray trim panel assembly.


5. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)

  1. B149208
    Pass the 3 rear seat belt floor anchors through the holes in the package tray trim panel assembly.

  1. Insert the rear end of the package tray trim panel assembly into the rear window shade assembly.

  1. Engage the 2 clips and install the package tray trim panel assembly.


6. INSTALL REAR SEAT SHOULDER BELT HOLE COVER

  1. B132014
    Engage the 4 claws and install the rear seat shoulder belt hole cover.


7. INSTALL REAR SEAT SHOULDER BELT COVER

  1. B132012
    Engage the 4 claws and install the rear seat shoulder belt cover.

    HINT:
    Use the same procedures for the RH side and the LH side.


8. CONNECT REAR SEAT OUTER BELT ASSEMBLY LH

  1. B147734E01
    Connect the floor end of the rear seat outer belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear seat outer belt assembly LH to overlap the protruding part of the floor panel.

  1. Check if the ELR locks.

    NOTICE:
    The check should be performed with the outer belt assembly LH installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.


9. CONNECT REAR SEAT OUTER BELT ASSEMBLY RH

  1. B147735E01
    Connect the floor end of the rear seat outer belt assembly RH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear seat outer belt assembly RH to overlap the protruding part of the floor panel.

  1. Check if the ELR locks.

    NOTICE:
    The check should be performed with the outer belt assembly RH installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.


10. INSTALL ROOF SIDE INNER GARNISH LH

  1. B132063
    Engage the 5 clips and 2 claws, then install the roof side inner garnish LH.


11. INSTALL ROOF SIDE INNER GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.


12. CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

  1. B151317E01
    Connect the floor end of the rear seat inner with center belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the protruding parts of the floor panel.

  1. Check if the ELR locks.

    NOTICE:
    The check should be performed with the outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.


13. INSTALL NO. 1 SEAT BRACKET (for Fixed Seat Type)
  1. Install the No. 1 seat bracket with the 2 nuts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


14. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

  1. B132080E02
    Install the rear door opening trim weatherstrip LH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.


15. INSTALL REAR DOOR SCUFF PLATE LH

  1. B132068
    Engage the 5 claws and 2 clips, then install the rear door scuff plate LH.


16. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

  1. B132082E01
    Install the rear door opening trim weatherstrip RH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.


17. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


18. INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)

  1. B136561
    Install the rear side seatback assembly with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


19. INSTALL REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)

HINT:
Use the same procedure for the RH and LH side.


20. INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)

  1. B136539
    Install the separate type rear seatback assembly with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


21. INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type)

  1. B134700
    Install the separate type rear seatback assembly with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


22. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type)

  1. B136577
    Place the seatback in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Install the rear seatback assembly with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. B136576
    Pass the 3 seat belts through and close the cap of the 2 rear seat shoulder belt guides.

  1. Install the floor anchor part with the bolt.


23. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (w/ Center Armrest)

24. INSTALL REAR SEAT HEADREST ASSEMBLY

25. INSTALL REAR SEAT CUSHION ASSEMBLY
for Fixed Seat Type: (Click here)
for Fold Down Seat Type: (Click here)
← INSTALLATION (Oct 2006 – May 2009)COMPONENTS (from Jun 2006) →