2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

PROBLEM SYMPTOMS TABLE

Troubleshooting · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

If a normal system code is displayed during the DTC check, but the problem still occurs, check the circuits for each problem symptom in the order given in the table below and proceed to the relevant troubleshooting page.

HINT:
  1. The following is the troubleshooting procedure for the wireless door lock control of a vehicle with the smart entry and start system.
  2. For the troubleshooting procedure for the wireless door lock control of a vehicle with the smart entry and start system, refer to the wireless door lock control system (without Smart Entry and Start System).
  3. Inspect the fuse and relay before investigating the suspected areas shown in the table below.
  4. Inspect each malfunction circuit in numerical order for its corresponding symptom.

WIRELESS DOOR CONTROL SYSTEM 
Symptom
Suspected Area
See page
The wireless door lock control system does not operate.
1. Perform the operation check
Click here
2. Check if the CAN communication DTC is output (for LHD)
Click here
3. Check if the CAN communication DTC is output (for RHD)
Click here
4. Door control transmitter
Click here
5. Door courtesy switch circuit (for 2GR-FE)
Click here
6. Door courtesy switch circuit (for 2AZ-FE)
Click here
7. Luggage compartment door courtesy switch (for 2GR-FE)
Click here
8. Luggage compartment door courtesy switch (for 2AZ-FE)
Click here
9. Power source circuit
Click here
10. Replace door control receiver
-
11. Replace certification ECU
-
12. If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)
-
The automatic lock function does not operate normally.
1. Perform the operation check
Click here
2. Door courtesy switch circuit (for 2GR-FE)
Click here
3. Door courtesy switch circuit (for 2AZ-FE)
Click here
4. If the symptoms still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)
-
The illuminated entry function only does not operate.
1. Perform the operation check
Click here
2. Lighting system (for 2GR-FE)
Click here
3. Lighting system (for 2AZ-FE)
Click here
4. If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)
-
The answer back function does not operate (Wireless door lock buzzer).
1. Perform the operation check
Click here
2. Lock position switch circuit (for 2GR-FE)
-
- Driver door
Click here
- Front passenger door
Click here
- Rear passenger door LH*
Click here
- Rear passenger door RH*
Click here
3. Lock position switch circuit (for 2AZ-FE)
-
- Driver door
Click here
- Front passenger door
Click here
- Rear passenger door LH*
Click here
- Rear passenger door RH*
Click here
4. Wireless door lock buzzer circuit
Click here
5. Replace certification ECU
-
6. If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)
-
The answer back function does not operate (Hazard warning light).
1. Perform the operation check
Click here
2. Lock position switch circuit (for 2GR-FE)
-
- Driver door
Click here
- Front passenger door
Click here
- Rear passenger door LH*
Click here
- Rear passenger door RH*
Click here
3. Lock position switch circuit (for 2AZ-FE)
-
- Driver door
Click here
- Front passenger door
Click here
- Rear passenger door LH*
Click here
- Rear passenger door RH*
Click here
4. Wire harness
-
5. Turn signal flasher assembly (for 2GR-FE RHD)
Click here
6. Turn signal flasher assembly (except 2GR-FE RHD)
Click here
7. If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)
-
The door ajar warning function only does not operate.
1. Perform the operation check
Click here
2. Door courtesy switch circuit (for 2GR-FE)
Click here
3. Door courtesy switch circuit (for 2AZ-FE)
Click here
4. If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)
-
The panic alarm function only does not operate.
1. Perform the operation check
Click here
2. Door control transmitter
Click here
3. If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)
-
The panic alarm function does not operate (Vehicle horn).
1. Perform the operation check
Click here
2. Horn circuit
Click here
3. If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)
-
The panic alarm function does not operate (Security horn).*
1. Perform the operation check
Click here
2. Security horn circuit
Click here
3. Replace certification ECU
-
4. If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)
-
The panic alarm function does not operate (Hazard warning light).
1. Perform the operation check
Click here
2. Wire harness
-
3. Turn signal flasher assembly (for 2GR-FE RHD)
Click here
4. Turn signal flasher assembly (except 2GR-FE RHD)
Click here
5. If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)
-
The panic alarm function does not operate (Headlight or taillight).
1. Perform the operation check
Click here
2. Lighting system (for 2GR-FE)
Click here
3. Lighting system (for 2AZ-FE)
Click here
4. If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)
-

HINT:
*: Only for RHD

← PROBLEM SYMPTOMS TABLE (Oct 2006 – May 2009)TERMINALS OF ECU (Oct 2006 – May 2009) →