2006-2011 Camry Aurion · Service Manual STEERING

REMOVAL

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

3. REMOVE FRONT WHEELS

4. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

  1. C133501
    Secure the steering wheel with the seat belt in order to prevent rotation.

    HINT:
    This operation is useful to prevent damage to the spiral cable.

  1. C156702E01
    Remove the bolt and slide the steering intermediate shaft assembly.

    NOTICE:
    Do not separate the steering intermediate shaft assembly from the power steering link assembly.

  1. C156703E01
    Put matchmarks on the steering intermediate shaft assembly and the power steering link assembly.

  1. Separate the steering intermediate shaft assembly from the power steering link assembly.


5. SEPARATE TIE ROD ASSEMBLY LH
  1. Remove the cotter pin and the nut.

  1. C133488E01
    Using SST, separate the tie rod assembly LH from the steering knuckle.
    SST
    09628-00011  

    NOTICE:
    1. Hang SST with a string, etc. to prevent it from falling.
    2. Do not damage the front disc brake dust cover.
    3. Do not damage the ball joint dust cover.
    4. Do not damage the steering knuckle.


6. SEPARATE TIE ROD ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.


7. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

HINT:
Refer to the instructions for removal of the engine assembly (Click here for 2AZ-FE, Click here for 2GR-FE).


8. DISCONNECT PRESSURE FEED TUBE ASSEMBLY (for LHD)

  1. C148619E01
    Using SST, disconnect the pressure feed tube assembly (return tube side) from the power steering link assembly.
    SST
    09023-12701  

  1. C148620E01
    Using SST, disconnect the pressure feed tube assembly (pressure feed tube side) from the power steering link assembly.
    SST
    09023-12701  

  1. C156698
    Remove the bolt, nut, and separate the pressure feed tube clamp.


9. DISCONNECT RETURN TUBE SUB-ASSEMBLY (for 2AZ-FE RHD)

  1. C137080
    Slide the clip and disconnect the return tube sub-assembly.


10. REMOVE RETURN TUBE ASSEMBLY (for 2AZ-FE RHD)

  1. C137081E01
    Using SST, remove the return tube assembly from the power steering link assembly.
    SST
    09023-12701  


11. DISCONNECT PRESSURE FEED TUBE ASSEMBLY (for 2AZ-FE RHD)

  1. C137083E01
    Using SST, disconnect the pressure feed tube assembly from the power steering link assembly.
    SST
    09023-12701  

  1. C137085
    Remove the nut and separate the pressure feed tube clamp.


12. DISCONNECT RETURN TUBE SUB-ASSEMBLY (for 2GR-FE RHD)

  1. C137691
    Slide the clip and disconnect the return tube sub-assembly.


13. REMOVE RETURN TUBE ASSEMBLY (for 2GR-FE RHD)

  1. C137692E02
    Using SST, remove the return tube assembly from the power steering link assembly.
    SST
    09023-12701  


14. DISCONNECT PRESSURE FEED TUBE ASSEMBLY (for 2GR-FE RHD)

  1. C137694E01
    Using SST, disconnect the pressure feed tube assembly from the power steering link assembly.
    SST
    09023-12701  

  1. C156699
    Remove the nut and separate the pressure feed tube clamp.


15. REMOVE POWER STEERING LINK ASSEMBLY

  1. C156700
    Remove the 2 bolts, 2 nuts, and power steering link assembly.

    NOTICE:
    Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut fixed.


16. REMOVE POWER STEERING RACK HOUSING HEAT INSULATOR (for 2GR-FE LHD)

  1. C153167
    Remove the power steering rack housing heat insulator from the power steering link assembly.


17. REMOVE POWER STEERING RACK HOUSING HEAT INSULATOR (for 2GR-FE RHD)

  1. C153166
    Remove the bolt and power steering rack housing heat insulator from the power steering link assembly.


18. REMOVE TIE ROD ASSEMBLY LH

  1. C132045E01
    Put matchmarks on the tie rod assembly LH and the steering rack end sub-assembly.

  1. Loosen the lock nut, and remove the tie rod assembly LH and the lock nut.


19. REMOVE TIE ROD ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.

← REMOVAL (Oct 2006 – May 2009)DISASSEMBLY (from Jun 2006) →