2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter

Circuit diagnosis · Vehicles built from Jun 2009

DESCRIPTION

This circuit is necessary for the ASL (Automatic Sound Levelizer) built into the radio and display assembly.
Speed signals are received from the combination meter assembly and used for the ASL.
The ASL function automatically adjusts the sound data in order to enable to hear the clear audio sound even when vehicle noise increases (as vehicle noise increases, the volume is increased etc.).

HINT:
  1. A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.
  2. If a short occurs in an ECU, all systems in the diagram below will not operate normally.


WIRING DIAGRAM


for 2GR-FE
E192360E01

for 2AZ-FE
E192288E01

INSPECTION PROCEDURE


1. CONFIRM MODEL

Result:
Result
Proceed to
for 2GR-FE
A
for 2AZ-FE
B



B
Go to step 5
A


2. INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)

  1. E177787E31
    Check the output waveform.
    1. Remove the combination meter assembly with the connector(s) still connected.

    2. Connect an oscilloscope to terminal F2-12 (+S) and body ground.

    3. Turn the ignition switch on (IG).

    4. Turn a wheel slowly.

    5. Check the signal waveform according to the condition(s) in the table below.

      Item
      Condition
      Measurement terminal
      F2-12 (+S) - Body ground
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Wheel being rotated

      OK:
      The waveform is similar to that shown in the illustration.

      HINT:
      When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.

      Text in Illustration 
      *1
      Component with harness connected
      (Combination Meter Assembly)



NG
GO TO METER / GAUGE SYSTEM (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY ASSEMBLY - COMBINATION METER ASSEMBLY)
  1. Disconnect the F8 radio and display assembly connector.

  1. Disconnect the F2 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F8-3 (SPD) - F2-12 (+S)
    Always
    Below 1 Ω



NG
Go to step 4
OK

REPLACE RADIO AND DISPLAY ASSEMBLY (for 2GR-FE RHD) (Click here)

4. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY ASSEMBLY - NO. 3 JUNCTION BLOCK)
  1. Disconnect the 3T No. 3 junction block connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F8-3 (SPD) - 3T-9
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 3 JUNCTION BLOCK)

5. INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)

  1. E196878E01
    Check the input waveform.
    1. Remove the combination meter assembly with the connector(s) still connected.

    2. Connect an oscilloscope to terminal F1-11 (+S) and body ground.

    3. Turn the ignition switch on (IG).

    4. Turn a wheel slowly.

    5. Check the signal waveform according to the condition(s) in the table below.

      Item
      Condition
      Measurement terminal
      F1-11 (+S) - Body ground
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Wheel being rotated
      Text in Illustration 
      *1
      Component with harness connected
      (Combination Meter Assembly)

      OK:
      The waveform is similar to that shown in the illustration.

      HINT:
      When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.



NG
GO TO METER / GAUGE SYSTEM (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY ASSEMBLY - COMBINATION METER ASSEMBLY)
  1. Disconnect the F8 radio and display assembly connector.

  1. Disconnect the F1 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F8-3 (SPD) - F1-11 (+S)
    Always
    Below 1 Ω



NG
Go to step 7
OK

REPLACE RADIO AND DISPLAY ASSEMBLY (except 2GR-FE RHD) (Click here)

7. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY ASSEMBLY - NO. 3 JUNCTION BLOCK)
  1. Disconnect the 3T No. 3 junction block connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F8-3 (SPD) - 3T-9
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 3 JUNCTION BLOCK)


← Black Screen (from Jun 2009)Steering Pad Switch Circuit (from Jun 2009) →