2006-2011 Camry Aurion · Service Manual BRAKE

C1249/49 Open in Stop Light Switch Circuit

Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

This circuit recognizes brake operation by sending a stop light signal to the skid control ECU.
The skid control ECU has an open detection circuit, which outputs this DTC when detecting an open in the stop light signal input line (STP terminal) or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).
DTC No.
DTC Detecting Condition
Trouble Area
C1249/49
Stop light switch circuit is open, and stop light switch voltage is 40% or more and less than 67% of the battery voltage.
  1. Stop light switch
  2. Stop light switch circuit
  3. Brake actuator assembly (Skid Control ECU)

WIRING DIAGRAM

C145717E06
C154356E02

INSPECTION PROCEDURE

HINT:
Check the condition of each related circuit connector before troubleshooting (Click here).


1. CHECK STOP LIGHT SWITCH OPERATION (STOP LIGHT SWITCH CIRCUIT)
  1. Check that the stop lights come on when the brake pedal is depressed and goes off when the brake pedal is released.

    OK:
    Pedal Condition
    Illumination Condition
    Brake pedal depressed
    ON
    Brake pedal released
    OFF



NG
Go to step 5
OK


2. INSPECT SKID CONTROL ECU CONNECTOR (STP TERMINAL)

  1. C131970E08
    Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A25-20 (STP) - Body ground
    Brake pedal depressed
    8 to 14 V
    A25-20 (STP) - Body ground
    Brake pedal released
    Below 4.0 V



NG
Go to step 7
OK


3. INSPECT SKID CONTROL ECU CONNECTOR (GND TERMINAL CONTINUITY)

  1. C131970E05
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    A25-4 (GND1) - Body ground
    Below 1 Ω
    A25-1 (GND2) - Body ground
    Below 1 Ω

  1. Connect the connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


4. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is recorded (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.


    Result:
    Condition
    Proceed to
    DTC is not output
    A
    DTC is output (When troubleshooting in accordance with the DTC CHART)
    B
    DTC is not output (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE)
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)

5. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH POWER SOURCE TERMINAL VOLTAGE)

  1. I042363E26
    Disconnect the stop light switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A19-2 - Body ground
    Always
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


6. INSPECT STOP LIGHT SWITCH ASSEMBLY

  1. C124796E11
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch pin free
    Below 1 Ω
    1 - 2
    Switch pin pushed in
    10 kΩ or higher



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH TO SKID CONTROL ECU)

  1. C132984E03
    Disconnect the stop light switch connector and skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    A25-20 (STP) - A19-1 (STP)
    Below 1 Ω

  1. Connect the connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH TO SKID CONTROL ECU)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT CIRCUIT)


← C1249/49 Open in Stop Light Switch Circuit (Jun 2006 – Sep 2006)C1249/49 Open in Stop Light Switch Circuit (from Jun 2009) →