Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION ANTENNA CORD (for 2GR-FE RHD)
REMOVAL
Removal / installation · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
1.
PRECAUTION
(Click here )
2.
ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
3.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment (Click here ).
4.
REMOVE LOWER NO. 3 STEERING WHEEL COVER
Using a screwdriver, disengage the claw and remove the No. 3 lower steering wheel cover.
HINT:
Tape up the screwdriver tip before use.
5.
REMOVE LOWER NO. 2 STEERING WHEEL COVER
Using a screwdriver, disengage the claw and remove the No. 2 lower steering wheel cover.
HINT:
Tape up the screwdriver tip before use.
6.
REMOVE STEERING PAD
Using a "TORX" socket (T30), loosen the 2 "TORX" screws until the groove along the screw circumference catches on the screw case.
Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand.
NOTICE:
When removing the steering pad, do not pull the airbag wire harness.
Disconnect the horn connector from the steering pad.
Disconnect the 2 airbag connectors and remove the steering pad.
NOTICE:
When handling the airbag connector, take care not to damage the airbag wire harness.
7.
REMOVE STEERING WHEEL ASSEMBLY
Remove the steering wheel assembly set nut.
Put matchmarks on the steering wheel assembly and the steering main shaft.
Disconnect the connectors from the spiral cable.
Using SST, remove the steering wheel assembly.
SST
09950-50013
(09951-05010, 09952-05010, 09953-05020, 09954-05031)
8.
REMOVE FRONT DOOR SCUFF PLATE RH
HINT:
Use the same procedure for the RH side and the LH side.
9.
REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH
HINT:
Use the same procedure for the RH side and the LH side.
10.
REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
Remove the bolt <D> and the screw <F>.
Disengage the 2 claws and the DLC3.
Disconnect the hood lock control cable assembly.
Disengage the claw and the 4 clips.
Remove the air hose, disconnect each connector, and then remove the lower No. 1 instrument panel finish panel.
11.
REMOVE STEERING COLUMN COVER
Remove the 2 screws <A>.
Disengage the 2 claws <a> and remove the lower steering column cover.
Disengage the claw <b> and remove the upper steering column cover.
12.
REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.
Using pliers, grip the claws of the clip and remove the turn signal switch assembly with spiral cable sub-assembly.
13.
REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY
Disengage the 3 claws and the 2 clips.
Disconnect each connector and remove the No. 1 instrument panel sub-assembly.
14.
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/o Smart Entry and Start System)
Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.
15.
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/ Smart Entry and Start System)
Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.
Disconnect the connector.
16.
REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Remove the 2 clips.
Disengage the guide and 4 claws, and then remove the instrument cluster finish panel sub-assembly.
17.
REMOVE COMBINATION METER ASSEMBLY
Remove the 4 screws <B>, <C> or <H>.
Disconnect each connector and remove the combination meter assembly.
18.
REMOVE FRONT DOOR SCUFF PLATE LH
Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.
19.
REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
Remove the cowl side trim clip.
Disengage the 2 clips and remove the cowl side trim sub-assembly LH.
20.
REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY
Disengage the 4 claws.
Disengage the 2 guides and remove the No. 2 under cover sub-assembly.
21.
REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
Remove the bolt <D>.
Remove the screw <F> or <N>.
Remove the 3 screws <F>.
Disengage the 3 claws and the 3 clips, and then remove the lower instrument panel sub-assembly.
22.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
23.
REMOVE UPPER CONSOLE PANEL FRONT GARNISH
Apply protective tape to the area shown in the illustration.
Using a moulding remover, disengage the 3 claws as shown in the illustration.
Using a moulding remover, disengage the 3 claws and remove the upper console panel front garnish as shown in the illustration.
Disconnect each connector.
24.
REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY
Apply protective tape to the area shown in the illustration.
Using a moulding remover, disengage the 2 claws as shown in the illustration.
Apply protective tape to the area shown in the illustration.
Using a moulding remover, disengage the 2 claws as shown in the illustration.
Disengage the 6 claws and remove the upper console panel sub-assembly as shown in the illustration.
Disconnect the connector.
25.
REMOVE INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY
Apply protective tape to the areas shown in the illustration.
Using a moulding remover, disengage the 6 claws as shown in the illustration.
Using a moulding remover, disengage the 5 claws as shown in the illustration.
Disconnect each connector and remove the instrument panel No. 2 register assembly.
26.
REMOVE CONSOLE BOX CARPET
Remove the console box carpet.
27.
REMOVE CONSOLE BOX ASSEMBLY
Disengage the clamp.
Remove the 3 screws <H>.
Remove the 3 screws <H>.
Remove the 2 bolts <I>.
Disengage the 2 claws and remove the console box assembly.
28.
REMOVE NAVIGATION RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY
Remove the 4 bolts.
Pull the navigation receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.
Disconnect each connector and remove the navigation receiver with heater control panel assembly.
29.
REMOVE FRONT PILLAR GARNISH LH
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 2 claws and remove the front pillar garnish LH.
Remove the clip <A> from the vehicle body.
Protect the curtain shield airbag assembly. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.
NOTICE:
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.
30.
REMOVE INSTRUMENT PANEL NO. 1 REGISTER ASSEMBLY
Disengage the 4 clips and remove the instrument panel No. 1 register assembly.
31.
REMOVE INSTRUMENT PANEL NO. 1 SPEAKER PANEL SUB-ASSEMBLY
Disengage the 6 claws and the 2 clips.
Disengage the 2 guides and remove the instrument panel No. 1 speaker panel sub-assembly.
32.
REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)
Remove the 2 bolts and front No. 2 speaker assembly.
Disconnect the connector.
33.
REMOVE FRONT PILLAR GARNISH RH
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 2 claws and remove the front pillar garnish RH.
Remove the clip <A> from the vehicle body.
Protect the curtain shield airbag assembly. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.
NOTICE:
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.
34.
REMOVE INSTRUMENT PANEL NO. 3 REGISTER ASSEMBLY
Disengage the 4 clips and remove the instrument panel No. 3 register assembly.
35.
REMOVE INSTRUMENT PANEL NO. 2 SPEAKER PANEL SUB-ASSEMBLY
Disengage the 6 claws and the 2 clips.
Disengage the 2 guides and remove the instrument panel No. 2 speaker panel sub-assembly.
36.
REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)
HINT:
Use the same procedure for the RH side and the LH side (Click here ).
37.
DISCONNECT INSTRUMENT PANEL WIRE ASSEMBLY
Disconnect the connector (yellow colored one).
38.
REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
Disengage each clamp.
Disconnect each connector.
Remove the bolt <E>.
Remove the 2 passenger airbag bolts <M>.
Remove the 2 bolts <J>.
Remove the 2 nuts <L>.
Disengage the 5 claws and remove the instrument panel safety pad assembly.
39.
REMOVE SIDE NO. 1 DEFROSTER NOZZLE DUCT
Remove the screw <H> and the side No. 1 defroster nozzle duct.
40.
REMOVE SIDE NO. 2 DEFROSTER NOZZLE DUCT
Remove the screw <H> and the side No. 2 defroster nozzle duct.
41.
REMOVE DEFROSTER NOZZLE ASSEMBLY
Remove the 3 screws <H> and the defroster nozzle assembly.
42.
REMOVE NO. 1 HEATER TO REGISTER DUCT
Remove the 3 screws <H> and the No. 1 heater to register duct.
43.
REMOVE NO. 3 HEATER TO REGISTER DUCT
Remove the 3 screws <H> and the No. 3 heater to register duct.
44.
REMOVE NO. 2 HEATER TO REGISTER DUCT
Remove the 2 screws <H> and the No. 2 heater to register duct.
45.
REMOVE NAVIGATION ANTENNA ASSEMBLY
Disengage the 3 clamps.
Remove the 2 screws and navigation antenna assembly.