2006-2011 Camry Aurion · Service Manual BRAKE

REMOVAL

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

HINT:
  1. Use the same procedure for the No. 2 parking brake cable assembly and No. 3 parking brake cable assembly.
  2. The procedures listed below are for the No. 3 parking brake cable assembly.


1. REMOVE PARKING BRAKE LEVER SUB-ASSEMBLY

HINT:
Refer to the procedures up to "REMOVE PARKING BRAKE LEVER SUB-ASSEMBLY". (Click here)


2. REMOVE PARKING BRAKE PEDAL ASSEMBLY (for LHD)

HINT:
Refer to the procedures up to "REMOVE PARKING BRAKE PEDAL ASSEMBLY (for LHD)". (Click here)


3. REMOVE PARKING BRAKE PEDAL ASSEMBLY (for RHD)

HINT:
Refer to the procedures up to "REMOVE PARKING BRAKE PEDAL ASSEMBLY (for RHD)". (Click here)


4. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for Lever Type Parking Brake)

  1. C131912
    Using a screwdriver, pull up the parking brake lever claw.

  1. C132670E01
    Remove the lock nut, the No. 1 wire adjusting nut, and the No. 1 parking brake cable assembly from the parking brake lever sub-assembly.


5. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for Pedal Type Parking Brake)

  1. C132698
    Using a screwdriver, pull up the parking brake pedal claw.

  1. C132697
    Remove the lock nut and the No. 1 wire adjusting nut.

  1. C132696
    Using needle-nose pliers, remove the clip and the No. 1 parking brake cable from the parking brake pedal assembly.


6. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Pedal Type Parking Brake)

  1. C133446
    Separate the No. 3 parking brake cable assembly from the parking brake equalizer.


7. SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY (for Pedal Type Parking Brake)

  1. C133455
    Separate the No. 2 parking brake cable assembly from the parking brake equalizer.


8. REMOVE NO. 4 PARKING BRAKE CABLE ASSEMBLY (for Pedal Type Parking Brake)

  1. C132655
    Slide the rubber boot as shown in the illustration.

  1. C132657
    Remove the No. 4 parking brake cable assembly from the parking brake equalizer as shown in the illustration.


9. REMOVE CENTER EXHAUST PIPE ASSEMBLY (for 2AZ-FE)

  1. Remove the 2 bolts, 2 nuts and center exhaust pipe assembly.

    A146049

  1. Remove the gasket from the front exhaust pipe.


10. REMOVE EXHAUST TAIL PIPE ASSEMBLY (for 2GR-FE)

  1. Remove the 4 nuts and 2 exhaust tail pipes.

    A146044

  1. Remove the 2 gaskets from the exhaust tail pipes.


11. REMOVE EXHAUST CENTER PIPE ASSEMBLY (for 2GR-FE)

  1. Remove the 2 bolts, 2 nuts and exhaust center pipe assembly.

    A146045

  1. Remove the gasket from the exhaust front pipe assembly.


12. REMOVE NO. 2 FRONT FLOOR HEAT LOWER INSULATOR (for 2AZ-FE)

  1. C132669
    Remove the 3 nuts and the No. 2 front floor heat lower insulator.


13. DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

  1. C141952
    Using needle-nose pliers, remove the clip.

  1. Turn and disconnect the No. 3 parking brake cable assembly as shown in the illustration.


14. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY

  1. C138186E02
    Using needle-nose pliers, remove the clip from the No. 3 parking brake cable assembly.

  1. Remove 3 bolts (A), bolt (B), and nut (C), and disengage each claw.

    C132668E03

  1. Remove the No. 3 parking brake cable assembly from the body.

  1. C132667E01
    Remove the parking brake cable clamp.

← REMOVAL (Oct 2006 – May 2009)INSTALLATION (Jun 2006 – Sep 2006) →